FRSS2623AD2 Frigidaire Refrigerator - Instructions

Removed ice bucket from freezer. Remove ice. Remove 2 phillips head screws from the inside front of ice bucket, and 2 fromt the bottom front to remove the front cover. Remove the E clip and washer from ice crusher shaft. Remove 4, 1/4” head screws from ice crusher housing. Unclip the selector shaft from crusher door paying attention to position.Slide housing off of shaft and discard. Install new housing over shaft and install the 4 screws. Install selector shaft into door. Install the E clip and washer onto shaft. Install front housing with the 4 screws previously removed. Refill bucket with ice and install bucket back into freezing taking care to orient the ice screw shaft into the cog in the back of the freezer as well as the door selection shaft. Test operation.

Remove ice drawer ,Removed front of drawer 4 screws ,Removed broken crusher 3 screws Ordered new parts reassembled replaced fix blade spacer that was broken and blade cover housing reattached front of drawer !

I followed the instructions, my ONLY issue was about the Part 46 the Ice Dispenser Actuator Rod. The front of the arm has flared out grooves and it didn't warn me about making sure the rod is properly aligned thru part 23 Front Plate or else when the ice maker actuates the rod it will not move properly if the grooves are not aligned on each side of the Front panel. I hope you can understand what I mean, if not just look at how the Part 46 rests in Part 23

Called "local" repair warehouse and ordered part. They shipped the wrong part. Went on-line to Part Select and got the right part.

I was able to replace the housing by only removing the front cover, the e-ring and washer and the 3 hex-head screws. I was able to work the old housing around to get the actuator arm off and then get it properly inserted into the new housing. Attach the new housing, IMPORTANT: make sure you get the fixed-blades and spacer assembly in the slot of the housing that holds them in place, replace the e-ring and washer, check that the actuator arm operates the door properly and replace the front cover. The videos can be helpful but these shortcuts will save some time.

The part i recieved, from parts select was a larger in circumfrence (<1/4) than the original. However i was not aware of this until after i treid to repair it.

I removed the broken fan from the condenser. This was very sipmle.

When i pluged the refridgerator back in to the outlet the fan tried to start up but soon began to make aloud noise, due to there not being enough clerance.

Removed shelves above the problem area. Tilted new shelf up to slide prongs into openings on one side, pushed in far enough to allow prongs on the other side to fit into their openings. Evened the shelf out then added some thick tape to both sides of the shelf to keep it from falling out.

Open freezer
Pry the switch out (bottom first, then push the tab on top while prying out)
Move wires to
New switch
Push switch in
Test

I BOUGHT 2 MORE SHELVES AND INSTALLED THEM.
THANK YOU

I looked at the internet before I purchased a new seal and saw how to repair it. It was a matter of pulling out the old seal and just popping in the new. The internet said to use a hair dryer to melt the rubber to adhere to the fridge in places where it wasn't. It was quick!

This was the last step of serial repairs to the ice crusher portion of the ice maker. I have practically replaced the entire assembly. All the blades were installed incorrectly (at factory? Afterwards?) and had bent. That caused problems for other parts. I hadn't noticed that the housing was weakened and my prior repair I did something dumb and the door on housing wasn't closing properly, so it snapped. I bought a new housing and installed it. My #1 tip is WATCH THE VIDEO! There are some things that have to be put together just so. You need things to line up and be under slight tension from springs. Last time I had it under too much tension. The door got in the way of the blades and broke. So this time I was more careful to do it correctly. Everything is working perfectly now. This design is clever, and I feel like I can diagnose and fix it again in future. "Steve's" instructional videos are a huge help. He shows exactly what to do.

Had to replace with a whole new part, had to take it all apart to replace

First I defrosted the entire unit, both sides for 24 hours. Restarted, I now have water dispensing. (It had apparently frozen) Next I took out the ice crushing part and took it apart, (a few screws) by removing the broken floppy piece; the small plastic floppy door that allows ice to crush, replaced this small piece, rather than replacing the entire big plastic piece that I ordered. Used a slot screw driver removed the old floppy piece that was broken and removed the same piece from the new one and switched them out. Reassembled the entire unit (a few screws), put the ice back in and it works great. I got the instructions for taking apart this from this site, however, it was fairly easy to figure out. Just be patient with the plastic parts.

I followed the YTube video. The ice maker doesnot crush ice. The auger moves the ice to the dispenser. Is there a position for metal blades when assembling auger?

Followed instructions in video that was suggested when I placed the order.