BZ22QW Caloric Refrigerator - Instructions

I checked your web site for similar problems. Most were the bimetal defrost thermostat. Some had defrost timer problems. Althought my bimetal thermostat was deformed by the ice I replaced both parts. The fix was easy after defrosting the evaporator. By using the spec sheets I found the locations and replaced the parts. The refrigerator is now working fine.

We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing

Had to defrost the freezer which takes most of the time. Once freezer is defrosted its a simple matter of disassembling and removing the cover which covers the evaporator and disconnecting the defrost thermostat and replacing with the new one then reassembling. The information provided at the Parts Select site was all I needed to get the repair done.

unplug refrigerator,remove content [shelves] then remove panel screws,slide thermostat from tube and unplug both wire ends,match up both thermostat[old unit have male round connector] you'll need round connector.cut old unit wire off,cut new unit wire,strip both ends join with solder and cover with heat-shrink and reinstall,fridge is cooling now.

bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what is inside the refer!

Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.

I did not do the repair myself as I am an elderly lady but am lucky enough to have a son-in-law who is very capable in many areas. He removed the old handle by loosening the screws with a Philips screwdriver. He attached the new handle likewise.
Service from your Co. and repair service could not have been better.
Thank You

At first I went to a local part supplier and they didn't have it in stock but could order it for me for $55.00 plus $10.00 to ship it. I told them I would have to think about it. I went home and got on the computer and found your web site and was I shocked when I saw the same part listed for $6.98 and $7.00 to ship it. You guys saved me $50.00. The part arrived in two day and took 5 min. to install. I now have light in my refrigerator. Thank you.

remove frozen food. take back panel off. use hair dryer to dethaw finned part. swapped defrost thermostat.one lead ok, other had to cut ends and wire splice together. replace panel and food. took care of problem, food in fridge stays cold. totally impressed with delivery time. ordered mon here tuesday. awesome..........

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

Used a screwdriver to pry loose the old switch, swapped wires to the new switch and pushed it into the opening. Took about 2 minutes.

By watching a video.

A very cold and brittle switch in a 17 year old fridge. Used screwdrivers to pry out with some resistance Had to cut the molded plug in half and split wires, because replacement contacts were farther apart than the original. End result, works great.

disconnected el. power to fridge. pried out broken switch with small screwdriner and pulled out w/water pump pliers. installed new switch and pressed into opening.

After disconnecting the electricity. I followed the instructions as indicated in the "HOW TO" article on the website. I used a steel putty knife and pried the light switch out of its retaining hole. I worked the right side the most since this is the side with the retaining clip. After I removed the switch I transferred the two electrical outlets to the new switch and easily snapped it into place. Engaged the electric power and tested the switch.