GB2026LEKS13 Amana Refrigerator - Instructions

Just plugged it in

The switch fix but did not fix the problem. I assumed the wires go on the same way as on the old switch. Is it possible if one light Burns out, the other will not work either?

1. Removed both crisper drawers. 2. Removed glass 3. Philips head screwdriver to remove the 2 screws securing guide rail. 4. 1/4" nut driver to remove the 3 screws holding the End Cap than removed and replaced with new one. Done.

First remove the snack drawer, glass shelf above it and other plastic pieces which just sit in place. Remove the three 1/4" screws that hold the end cap to the refrigerator liner. Lift up on the endcap and then out as there is a blind slot it slides into. Tilt the endcap out from the back and remove it. Remove the drawer glide from the endcap and transfer it to the new part. Reinstall the endcap by engaging the two plastic ends into the rear corner of the cabinet and then sliding it down on over the blind support. Install the three 1/4" head screws to secure the endcap to the liner. Reinstall the glass shelf and pantry drawer.

Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.

Popped out the old switch and replaced it with the one dying

The Condenser Fan Motor was already removed due to searching for the problem. The new fan motor looked different from the original but I felt very comfortable that Part Select had sent me the new part showing original part number changing numbers over the years. Simply placed the fan blades onto the new motor lined up 2 of the holes placed screws and tightened then plugged the wire ribbon into the Condensor Fan Motor, plugged in the Refridgerator and it worked beautifully.

The instruction video on the Part Select Web Site made it so incredibly easy to install. Installation took under 3 minutes!

Opened package. Washed divider. Dropped in place (where indicated by marks) in drawer. Took a nap.

I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.

First, turn off the refrigerator so the open door alarm doesn't drive you crazy while you are working with the refrigerator doors open! Then, remove both crisper drawers, remove deli drawer, remove deli cover from two pins (one was already broken), remove the bottom glass shelf and the plastic glass support. None of this requires any tools, all just slide or lift out. Then, using a nut driver remove the two screws holding the drawer slide from the pantry end cap. You access one of the screws from an opening while the slide is all the way in. This is where I needed needle nose pliers to remove the screw from the opening after it was unscrewed - if your nut driver is magnetic you won't need the pliers. To access the second screw, pull the slide all of the way out. Then you remove the broken end cap by unscrewing 3 screws with the nut driver. Once the screws are removed, you lift up on the front of the end cap to loosen it from a catch on the inside and then pull the end cap out. Install the new end cap by sliding the two tabs into the back of the refrigerator and then pushing down on the end cap to set it in the catch. Now replace the screws, re-attach the slide with the two screws, reinstall the glass and the drawers and then reinstall the drawer cover by slipping it into the pins on each side (be careful when depressing the pins, do it gently or they may break off). Turn the refrigerator back on. You are done These instructions make it sound much more difficult than it actually is, it takes as long to remove and replace the drawers and it does to do the actual installation of the end cap..

I removed the crisper drawers and glass shelf and set them aside. Used a nut driver (maybe 5/16") to unbolt the old endcap as well as the back piece which it was attached to. I had to study the damper system a bit so I could figure out how to put it back together, took some quick snaps with the digital camera to be sure I wouldn't flub it. I transferred all of the misc plastic bits which make up the damper system into the new endcap and bolted it back in.

bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what is inside the refer!

We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing

Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.

Slick as a whistle