Models > GB2026REKS4 > Instructions

GB2026REKS4 Amana Refrigerator - Instructions

Jump to:

All Instructions for the GB2026REKS4
121 - 135 of 351
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
CHRISTINE from MARBLEHEAD, OH
Parts Used:
WPW10534153
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
Needed to replace old kickplate as it no longer was attached
Put new one on matching the sctew feet and design of the grill
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michael from McKinney, TX
Parts Used:
W10619951
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver
Water pooling on the floor.
This problem is caused by a "Duckbill" rubber grommet attached to the bottom drain tube of the freezer. This duckbill opens up during the defrost cycle and allows water to drain down the "water slide" to the evaporator pan. It doesn't take much to gum the Duckbill. Once gummed up the defrost water is trapped. The Defrost Cycle eventually makes the water flow out of the coil area to the bottom of the freezer then eventually to the floor. The repair involves unplugging the unit, removing the bottom back cover with a 1/4 nut driver, pop the power clip out to give you room, reach in and pull the duckbill grommet and the water slide, then installing this replacement drain kit. This is a p trap replacement that actually fixes the root cause of this problem. A tricky part is removing the water slide, you can see the white snap that holds the slide in place. Using a small flat blade from the top releases the snap and the unit is pulled upward rather easily. This replacement drain clip snaps in the same place. If I had to do this again it wouldn't take more than two minutes to replace. Oh, one major thing, you need to manually defrost the unit. I pulled the front door off, it is held with 4 screws ... don't remove them just loosen them and it pops off easily. I pulled the bottom tray out an it gave me room to squirt hot water with a baster into the back freezer area. Eventually everything thawed out. If I had it to do over I would have waited on connecting the tube to the evaporator pan and placed the bottom of the tube into a small sauce pan or something to collect the drain water and easily dump it into the sink. I used a sponge and that took forever. BTW, just to reiterate, use this item and not that Duck Bill for replacement, this actually fixes the root cause of this problem!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Anne from South Berlington, VT
Parts Used:
WP12656018
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
Pin that holds the crisper/pantry lid broke off and arm needed to be replaced.
Removed the drawer and shelf above to get access to drawer slide. Removed slide with socket wrench. Also need to remove, then reinstall the arm that is attached to right side end cap that adjusts the temperature flow into the pantry drawer. Reattaching it was not obvious so it took awhile to figure out how it fit. Written instructions would have helped. The part did not come with anything.
This is the second end cap that has required replacing. The first was on the left so did not involve the temperature adjustment arm.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Lou Sousa from Attleboro Falls, MA
Parts Used:
WP12656018
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Pivot bracket for vegetable crisper broke off.
a) removed screws with nutdriver
b) took out old piece
c) disassembled good parts from broken piece
d) reassembled good parts on new piece.
e) reattached new piece
f) reattached door to crisper.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Bob from Colorado Springs, CO
Parts Used:
WP12656105
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Wrench set
The tab that the tray door rotates on broke. This is the second time it broke. Very bad design.
I did it quickly since this was the second time it broke. For easier access, remove the glass shelf above the drawer and the two plastic strips that hold it in place. Remove the two screws (yes, there are three screw holes on each side, but there are screws in only the front and center positions; probably to save money on screws) with either a flathead screwdriver or a socket wrench, which works better. There are two tabs on the end cap that slide into slots in the back of the refrigerator. There is also a plastic retainer on the side of the refrigerator in the front that attaches to the end cap. Gently lift up the front of the end cap and pull forward to remove it. Then unscrew and remove the metal slide bars and install them on the new end cap. Then do everything in the reverse order. Fit the two tabs into the slots in the back of the fridge, then position the fitting over the plastic retainer on the side of the fridge, and gently push back and down. Then screw the end cap back in place. Repplace the two strips for the glass shelf and then slide the shelf back into position. The last thing is to refit the tray door onto the tabs on both end caps. Slide it into position onto one end cap tab, then GENTLY push the tab back on the other side and fit it into position on the tray cover.

This sounds more complicated than it is, but there are no instructions with the replacement piece, which in my opinion is bad for customer relations. This is also a really bad design. If you accidentally leave the tray door open when you close the refrigerator door, the refrigerator door will hit the tray door and break one of the tabs.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Vincent from Whitestone, NY
Parts Used:
WP12656105
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Clip on left hand side that holds Pantry cover broke.
1. Removed both crisper drawers. 2. Removed glass 3. Philips head screwdriver to remove the 2 screws securing guide rail. 4. 1/4" nut driver to remove the 3 screws holding the End Cap than removed and replaced with new one. Done.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Scott from Ortonville, MI
Parts Used:
WP12656018
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Broken hinge pin for the crisper.
Removed screws from the broken end cap and removed it. Installed the existing internal parts in the new end cap and reinstalled the screws. Very easy and the exploded diagrams on your site made it a very simple repair.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Maria from San Mateo, CA
Parts Used:
WP12656018
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
The endcap was broken and couldn't hold the pantry cover.
I had put off dealing with this repair thinking it would be too complicated and expensive. Was I fooled! I removed the vegetable drawers, shelf and pantry drawer. Then I removed two small bolts using a socket and power drill (very carefully). The entire piece just came right out. There's a small screw holding the air regulator onto the back wall of the refrigerator. This is all connected to the pantry cap, so it has to be removed as well. Once both pieces were out, I just carefully separated the air flow regulator from the borken end cap, attached the new piece, and then bolted/screwed everything back into place. Very easy and inexpensive!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ken from LK HAVASU CTY, AZ
Parts Used:
WPW10235370
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
The glide for the panty door broke and a new one was ordered.
The glide was very easy to put on; however it is easiest to put in the front screw first, due to the thickness of the glide. Pretty easy!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Joanne from Los Gatos, CA
Parts Used:
WP12656018
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
broken right side bracket
First I found I had to remove both of the bottom crisper trays and the glass shelf over the broken bracket.
Next I removed the bottom drawer slide held in with 2 Phillips head screws.
Then I used a 1/4 inch nut driver on my hand held drill to remove the 3 1/4 screws holding the broken bracket.
Then I had to figure out how to remove the air adjusting lever held in by clips and re-assemble it onto the replacement side bracket.
Then I re-installed the new bracket and the drawer slide and re-installed the glass shelf and the crisper trays.
Final step was to re-install the bottom tray and it's raising lid.
Done!

Done by Can Do Handyman Services.

mailto:[email protected]
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from Shrewsbury, MA
Parts Used:
W11396033
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Broken light switch
Pried out the old switch and installed the new switch.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
cookie from Amherst, MA
Parts Used:
WP12656018
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Wrench set
The little plastic nob that holds the drawer cover on cracked off. (terrible design and I am sure its a common problem.
I removed all of the drawers, and simply used the wrench set to loosen the three bolts holding the endcap and I used a screwdriver to loosen the plastic cover for the water hose. It took a minute or two to figure out how to unfasten the endcap from the other cover without snapping someother piece of plastic, but once I gently schimmied and squeezed the attached plastic the pieces came apart. Then it was just a matter of washing the refrig and replacing the parts. Snip/Snap.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from GROVESPRING, MO
Parts Used:
W11384469
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
light did not work on the refrigerator side
bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what is inside the refer!
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Justin from Huntersville, NC
Parts Used:
W11396033
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Light hinge broke
Repair was tremendously easy. All I did was remove old light switch by prying out with screw driver and plugging in the new light switch and pushing it into the hole. Simple! The instructions weren't needed, but they were very thorough.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
David Barnes from ROSWELL, NM
Parts Used:
W11384469
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Rocker on switch broke off
Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the GB2026REKS4
121 - 135 of 351