TP19AL-P1300602WL Amana Refrigerator - Instructions

Exposed evaporator and fan.Turned refer back on. Evaporator started to get cold but fan did not run. Removed fan and applied 115 volts. Fan did not run. Installed new fan kit. Old refer works as good as new. Vary easy job. I almost bought a new refer. Glad I didn't. Probably saved myself $500+ Shopped several sites on internet. Other sites wanted about the same price for motor only and 15-20 bucks more for the fan. Vary pleased that I found this company to buy this part. Received fan kit in just a few days.

It was easy after it was apparent that the run capacitor was plugged into the compressor. This was determined from a parts diagram of the actual model refrigerator. The part was the same but the location on the video was wrong. A large screwdriver was used to unplug the capacitor from the compressor. The temperature range of the refrigerator is still too wide but it's colder.

did not remove the doors. did freezer first ,removed inner door planel install gasget on panel and reinstalled. the aloney problem i had was trying to resape the door gasget on the big door. which is still a little out of shape hopeing it will fall in line over time.

removed old and instaslled new. biggest problem was getting to one of the screws.

I did not remove the door from the fridge deciding to replace the gasket while the door was still attached. Next time I will follow their suggestion to remove the door and lay it down. I didn't realize that when you take the screws out (And there are A LOT of screws!) the whole panel comes off the door. It also took a long time to clean the door and panel with years of dirt/mildew to deal with. I had a hard time trying to get the kinks out with a hair dryer, didn't seem to work. Putting the new one on and screwing it back in place was pretty easy (would have been easier if it was laying flat). There are a couple of places where the seal is not perfect because of the kinks, but not going to worry about that.

1) I took everything off the door.
2) I removed the door from the bottom because it was easiest doing it from the bottom
3) I layed the door on the table and proceeded to unscrew the panel that holds things
4) I removed the panel and the old gasket
5) I cleaned all around where the gasket was screwed to the door and we cleaned the panel and we cleaned the refrigerator where the seal touches the door.
6) I made sure it was all dry and I fitted the new gasket on the door and put the panel making sure it fit around the panel
7) I began replacing the screws starting at the second screw from the corner and I did all 4 corners then I proceeded to screw the screws further into the corner and finally screwed all the rest of the screws.
8) put the door back on the refrigerator.
Now be patient because at first when closing the door there are sections that you have to push on to make it seal and this can happens for about a week. But finally it seals.

I replaced the run capacitor wich is located near the compressor, i first turned power off to fridge than remuved capacitor checked for continuity and the capacitor was the problem thanks

The instruction sheet supplied with the new motor described the steps to take very good. Replaced the rubber grommets for the three motor mounts also. A flashlight or light source was needed or was very helpful.

Partition between Freezer and Fridge was running very hot. (Warm is normal). Oiling fan did not work. The only problems encountered in the replacement were getting fan out and in through coolant lines, cut plug off to accomodate generic fan wiring, getting the screws back in without cooking your hand on a hot compressor. Unit works great!

I removed the nuts that held the motor mount, then removed fan blade, cut the wires, and slid the motor pass the mounts and the coil shroud, Installed motor in reverse order. worked out ok.

Ordered new fan motor on line took out old motor and replaced with new one

removed lower back cover. diconnected fan ass'y electrical connection, removed fan housing (3 screws). removed fan motor from housing. cut old connector from fan and installed on new fan with wire nuts included. re-installed new fan to housing and re-installed housing to frame.

Removed the plastic cover cap on side screw the removed the three screws, removing the old handle. Cleaned screws and mounting area on door, then installed the new handle. Very easy.

With this order it wasn't so much the repair that was the issue but the fact that I needed the part right away. I broke the shelf Tuesday night and placed the order just afterwards. By Thursday afternoon I had received the new shelf; one day before my inlaws arrived to visit. I was surprised and relieved the part was in stock. Thanks!

I simply put the post in and set up the drawers and shelf.