SRD520TE-P1313101WE Amana Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- William from LaPlace, LA
- Parts Used:
- WPD7749401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice Maker Auger Jambed and Broke Helix
Removed 6 screws total and removed the entire Auger and Ice Crusher. The broken Helix just fell off, I put the new one on after a little finagaling to get it lined up right and it just snap into place. Replace the screws, put the bucket back, dumped in the Ice and the dispenser started working Fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Justin from Huntersville, NC
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light hinge broke
Repair was tremendously easy. All I did was remove old light switch by prying out with screw driver and plugging in the new light switch and pushing it into the hole. Simple! The instructions weren't needed, but they were very thorough.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RALPH from PARAMUS, NJ
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Refrigerator lamp not functioning
Had to push the light switch to get lamp to light up.
Removed power from refrig. and removed old light switch
and replaced with the one I got from Partselect. Turned power back on and was done.
Removed power from refrig. and removed old light switch
and replaced with the one I got from Partselect. Turned power back on and was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from GROVESPRING, MO
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
light did not work on the refrigerator side
bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what is inside the refer!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jesse from Slidell, LA
- Parts Used:
- WPD7749401
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
not distributing ice
1. Removed ice maker from frig.
2. Emptied all ice cubes.
3. Let it warm up to room temperature.
4. Removed front cover from bottom up (unsnapped).
5. Removed 4 screws.
6. Removed old helix cap.
7. Installed new helix cap.
8. Reverse of step 5 to step 1 above.
2. Emptied all ice cubes.
3. Let it warm up to room temperature.
4. Removed front cover from bottom up (unsnapped).
5. Removed 4 screws.
6. Removed old helix cap.
7. Installed new helix cap.
8. Reverse of step 5 to step 1 above.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Sandy, UT
- Parts Used:
- R0181181
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Replaced dorr closure cam on both doors of side-by-side
The fridge door was easy. Just unscrew top and lift off hindge. The freezer door took longer. But I had the user guide which helped. We unhooked the power harness at the top of the door, and disconnected the water line at the bottom of the door.
Frankly, it wasn't that hard for me because I had my son-in-law do it!
Frankly, it wasn't that hard for me because I had my son-in-law do it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from Lindenhurst, IL
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
icemaker
installed new parts
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Edmond, OK
- Parts Used:
- R0181181
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
The right door was sagging and the handles were rubbing together
First, remove the plastic cover off the top hinge by removing the single phillips head screw.
Removed the three hex-head screws holding the hinge to the body of the fridge and then lift the hinge off of the door.
Lift the door off the bottom hinge and place on a flat surface so you can easily access the bottom.
Remove the single hex-head screw from the center of the door part of the closure cam and pull it free. Install the new part.
Next, remove the bottom portion of the closure cam from the lower door hinge (still attached to the fridge) by removing the single hex-head screw. Install the new part.
If needed, lube the lower door hinge with Vaseline and carefully set the door back on. (This is the hard part if you are working alone, as it can be hard to line up the hole.)
Lube the top hinge, reinstall, and replace the plastic cover. Easy as 1, 2, 3.
Removed the three hex-head screws holding the hinge to the body of the fridge and then lift the hinge off of the door.
Lift the door off the bottom hinge and place on a flat surface so you can easily access the bottom.
Remove the single hex-head screw from the center of the door part of the closure cam and pull it free. Install the new part.
Next, remove the bottom portion of the closure cam from the lower door hinge (still attached to the fridge) by removing the single hex-head screw. Install the new part.
If needed, lube the lower door hinge with Vaseline and carefully set the door back on. (This is the hard part if you are working alone, as it can be hard to line up the hole.)
Lube the top hinge, reinstall, and replace the plastic cover. Easy as 1, 2, 3.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Topsail Beach, NC
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken refrigerator compartment light switch.
The best part of the repair was how easy it was to find and order the part. Instead of searching the parts houses around town I just went to the PartSelect web site, quickly found and ordered the part in about five minutes, received the part the next day at my home and was ready to make the repair. Wow! What a pleasure for something to work the way it was meant to. Removed old switch located by prying out with sharp knife or screwdriver. Don't worry about breaking it or cracking plastic. Disconnect(unplug) wires from back of switch. Replace (plug-in) wires on back of new switch. Insert in location of old switch. Finisheed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- albert from El Paso, TX
- Parts Used:
- WPD7749401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
end cap broke under tlhe weight of ice and other frozen items that were ill placed
removed the ice maker tray and screws and that held the cover to the rotating mechanism that crushes and dispenses the ice. the end cap is then attached to the rotating mechanism and ice container, the cover is replaced;finishing the job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Hinsdale, IL
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door Light switch cracked Mounting
I noticed that the refrigerator was having trouble maintaining temperature. Thought it might be time for new one until I found out that a new frig was $5k to $7K. Just happened to notice that the light switch didn't look quite right (was not sitting sqaure to the door). Once I pressed it it came loose. I then realized the the lights were staying on (50 watts of heating). Replaced the switch and the frig started working like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Mundelein, IL
- Parts Used:
- R0181181
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The door clicked when opened or closed.
I followed the other web notes with one change .Since I too forgot the lube , I used a pry bar and block of wood to lift the door and a tooth pick to glob some lube in the lower hinge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JACK from MT. CARMEL, IL
- Parts Used:
- WPD7749401, 10114401
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Ice would not eject
Just removed old parts and replaced with new parts
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cecelia from Beaver Dam, WI
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
light staying on
A very cold and brittle switch in a 17 year old fridge. Used screwdrivers to pry out with some resistance Had to cut the molded plug in half and split wires, because replacement contacts were farther apart than the original. End result, works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kent from fishers, IN
- Parts Used:
- R0181181
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Refrigerator door side lower closer cam broke
The worst part was unloading the door shelves. Removed upper hinge cover and hinge hex screws. This allows the door to be removed. Lay the door on side. Remove screw that holds cam in place. Replace
broken cam with new piece. Put the door back on the hinge pin and replace upper hinge screws and cover.
Now reload all of the stuff.
broken cam with new piece. Put the door back on the hinge pin and replace upper hinge screws and cover.
Now reload all of the stuff.
Was this instruction helpful to you?
Thank you for voting!