SRD526SL-P1184801WL Amana Refrigerator - Instructions

Replace the Auger & Crusher blade. Very easy to do and it works great now. Also, your customer service was great!! shipped the same day and arrived to me the next day!!

Simply stick a putty knife between the switch and refrig wall. Pop out old swith, remove both wires by pulling off switch by terminals. Throw switch out. Put wires on new switch and push into slot and all done. Nothing to it! Took me 5 minutes if th

I simply installed the shelf by placing the built in hooks in the door. I called the 800 number to order because I wasn't sure what the part was called. I received superb help from a real person!! The part arrived very quickly; within 2 days. I am very pleased to have the refrigerator intact again.

I watched the online video and followed the directions. The only thing that was not obvious (and this is where the video saved several minutes)was how to remove the upper part from the door. This repair makes the door seals much more effective and should reduce the compressor run time. I have to compliment you on your prices and speed in getting the parts to me...great service!

First My Frig side of the double door unit wasn't closing on its own. Kids don't look, so they walk away...next thing you know the frig warms up and the freezer starts to frost up from running so long...Now it won't shut off.... I checked the hinge and sure enough it was wore down. Now mind you, I ordered a hinge kit first without checking to see what type I needed...don't do that...Less than 15 mins you can take the door off and see which one you need.As soon as I saw which type of hinge set I needed I went and ordered it...returned the other one. It came pretty quick.... 15 mins had that sucker changed and working... But... the door still wouldn't close on its own... Common sense told me the heat from the frosted freezer caused the door and frig walls to swell... Yes I said the heat... When the component in the freezer frosts up it does not keep the frig cool, nor will the freezer stay kool... the frost prevents the cool air from moving around...thus "HEAT".... It took a full 24 hrs for my frig n freezer to get back to normal... and now the door closes just fine... MIND YOU! I had to take the covers off the freezer unit inside, then take a steamer and melt all that frost off of every inch including down the drain... That took me a good 5-6 hours... and what a mess.... but it was worth my time.... because I don't have to replace my second hand Jenn-Air which I could never afford to buy brand new.... Whew....what we have to do to keep things going... $11 bucks worth of parts.... "Super Mom" :o)

We tried repairing with a new switch which was very easy to install but it didn't fix the problem.

This is an easy fix, simply remove and replace. What I was impressed with is that a how to video was provided along with my part. I wish all manufactures would offer this, the video was easy to understand and you had a good view of the operation. Thanks, a job well done.

Removed broken arm, repositioned spring and reinstalled with new arm. Very Easy. I was suspicious as the part did not look like the old one, but the part info said that it would work with my model, and, of course, it did.

I watched the video and thought "I can do this". Made some notes and then proceeded to remove the old switch and replace with the new one. Thank you.

I have never before seen a bulb with the filament intact not light. If the bulb's filament seems intact, screw the bulb into a known working lamp and see if it lights. When screwing it back into the socket in the fridge, it takes a bit of extra effort to fully seat (until it does, it won't light!). For replacing the switch, I unplugged the unit, used a paint scraper and worked it under the switch bezel from the right side. A bit of moxie, and the switch came out. The replacement switch had a different spade contact spacing than the original. I used a pair of scissors to cut the rubber bridge between the two switch wire connectors so I could connect to the new switch. In the end, it turned out to be the bulb. NOTE: The Model TC18KL is _not_ listed! What I finally found that the number "P7803211WL" on the sticker is actually a manufacturing code. Found this out by searching, and Sears' part search came up with matches.

I had ordered some other parts for something entirely different off your website and service was great. So after almost ten years of a dark refrigerator, because of a defective switch, I decided to see if you had the part to fix it... You did and the part got here in 3 days. I had a working light switch and all the light in the world where my husband needed it most (in the fridge). It took me at the most ten minutes to replace the part. All is well now and I have a happy husband who can find the leftovers just fine. Thanks for your great service!

After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.

Ordered the replacement. Removed the old one, followed the instructions, installation was a snap.

Replaced cold water dispenser reservoir. Removed back access panel on bottom of refridgerator. Cut hoses using a wire cutter and removed old reservoir. Installed new unit (one screw). Routed hoses through bottom of refridgerator. Cut length to allow hose splicing just beneath resevoir. Connected hoses using hose splicers provided with the part. Musty taste is better if a couple glasses of water are run through the unit before drinking each time. Previously the water never got better. I think more hoses need to be replaced in the door to fully solve the problem. Repair took less than 30 minutes.

Looked up issue on the internet and found that other folks had the same problem and said it was probably the compressor starter. This is actually two parts, a capacitor and a capacitor relay. Wasn't sure which was causing the problem so made sure I ordered the part number which inscluded both. One plugs into the other. Easy enough to just unplug the parts from the side of the compressor. Plugged in the new parts and compressor kicked on. Evrything working as normal. No one locally had parts in stock so overnighted from Partselect.