SRD526TW-P1313401WW Amana Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Bob from Oakland, MD
- Parts Used:
- WPD7749401
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
broken end cap on ice icemaker bin
remove the tray from the freezer. unsnap the front cover from the bin. remove the four screws holding the metal helix and grinder assembly to the bin. slide the metal helix and grinder assembly out. slide the new end cap onto the end of the helix. (this is the only tricky part and takes some patience. The stub end of the helix has to slide into the hole in the end cap. You can't bend the helix, just work the end cap around until it slides over the helix end stub). Reassemble the grinder and helix to the bin, snap the cover on and slide back into the freezer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from GROVESPRING, MO
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
light did not work on the refrigerator side
bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what is inside the refer!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jesse from Slidell, LA
- Parts Used:
- WPD7749401
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
not distributing ice
1. Removed ice maker from frig.
2. Emptied all ice cubes.
3. Let it warm up to room temperature.
4. Removed front cover from bottom up (unsnapped).
5. Removed 4 screws.
6. Removed old helix cap.
7. Installed new helix cap.
8. Reverse of step 5 to step 1 above.
2. Emptied all ice cubes.
3. Let it warm up to room temperature.
4. Removed front cover from bottom up (unsnapped).
5. Removed 4 screws.
6. Removed old helix cap.
7. Installed new helix cap.
8. Reverse of step 5 to step 1 above.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from LaPlace, LA
- Parts Used:
- WPD7749401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice Maker Auger Jambed and Broke Helix
Removed 6 screws total and removed the entire Auger and Ice Crusher. The broken Helix just fell off, I put the new one on after a little finagaling to get it lined up right and it just snap into place. Replace the screws, put the bucket back, dumped in the Ice and the dispenser started working Fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynn from Southlake, TX
- Parts Used:
- 12321807Q
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
kick plate wouldn't stay on
i inserted the connectors to the kickplate and put it on the refrigerator. very easy...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Sandy, UT
- Parts Used:
- R0181181
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Replaced dorr closure cam on both doors of side-by-side
The fridge door was easy. Just unscrew top and lift off hindge. The freezer door took longer. But I had the user guide which helped. We unhooked the power harness at the top of the door, and disconnected the water line at the bottom of the door.
Frankly, it wasn't that hard for me because I had my son-in-law do it!
Frankly, it wasn't that hard for me because I had my son-in-law do it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Shrewsbury, MA
- Parts Used:
- W11396033
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Broken light switch
Pried out the old switch and installed the new switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from Lindenhurst, IL
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
icemaker
installed new parts
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Edmond, OK
- Parts Used:
- R0181181
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
The right door was sagging and the handles were rubbing together
First, remove the plastic cover off the top hinge by removing the single phillips head screw.
Removed the three hex-head screws holding the hinge to the body of the fridge and then lift the hinge off of the door.
Lift the door off the bottom hinge and place on a flat surface so you can easily access the bottom.
Remove the single hex-head screw from the center of the door part of the closure cam and pull it free. Install the new part.
Next, remove the bottom portion of the closure cam from the lower door hinge (still attached to the fridge) by removing the single hex-head screw. Install the new part.
If needed, lube the lower door hinge with Vaseline and carefully set the door back on. (This is the hard part if you are working alone, as it can be hard to line up the hole.)
Lube the top hinge, reinstall, and replace the plastic cover. Easy as 1, 2, 3.
Removed the three hex-head screws holding the hinge to the body of the fridge and then lift the hinge off of the door.
Lift the door off the bottom hinge and place on a flat surface so you can easily access the bottom.
Remove the single hex-head screw from the center of the door part of the closure cam and pull it free. Install the new part.
Next, remove the bottom portion of the closure cam from the lower door hinge (still attached to the fridge) by removing the single hex-head screw. Install the new part.
If needed, lube the lower door hinge with Vaseline and carefully set the door back on. (This is the hard part if you are working alone, as it can be hard to line up the hole.)
Lube the top hinge, reinstall, and replace the plastic cover. Easy as 1, 2, 3.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Topsail Beach, NC
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken refrigerator compartment light switch.
The best part of the repair was how easy it was to find and order the part. Instead of searching the parts houses around town I just went to the PartSelect web site, quickly found and ordered the part in about five minutes, received the part the next day at my home and was ready to make the repair. Wow! What a pleasure for something to work the way it was meant to. Removed old switch located by prying out with sharp knife or screwdriver. Don't worry about breaking it or cracking plastic. Disconnect(unplug) wires from back of switch. Replace (plug-in) wires on back of new switch. Insert in location of old switch. Finisheed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- albert from El Paso, TX
- Parts Used:
- WPD7749401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
end cap broke under tlhe weight of ice and other frozen items that were ill placed
removed the ice maker tray and screws and that held the cover to the rotating mechanism that crushes and dispenses the ice. the end cap is then attached to the rotating mechanism and ice container, the cover is replaced;finishing the job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Orleans, MA
- Parts Used:
- WP628356
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken ice maker arm mount
Pried out ice blade bar and removed broken water fill cup and replaced with new one.The whole repair costs $9.52 So I saved $ 190 over the cost of Appliance man visit!
It would have been $150& $50 for visit to replace ice maker unit.
It would have been $150& $50 for visit to replace ice maker unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fonce from Ft Lauderdale, FL
- Parts Used:
- R0181181
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
lower cam broke
Remove the grandkids pictures from the door then empty the contents inside the door. Remove the top hinge cover and the top hinge bracket. Lift the door off the bottom pivot. Replace the lower cam by removing one screw. With the door in the horizontal position, remove and replace the upper cam. Apply a little grease on both cam surfaces. Align the door before tightening the top bracket and your done. If you did not take a picture of the door before you started the project you will have to rely on memory to arrange the pictures in the proper location.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Milford, MI
- Parts Used:
- R0181181
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Plastic Cams on frig door cracked in halk/door wouldn't close easily
Removed the top hinge (4 screws)-lifted the door off of the lower hinge-replaced both halves of the cam kit and mounted the door and reattached the upper hinge.
Probably took about fifteen minutes total.
Probably took about fifteen minutes total.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Smyrna, GA
- Parts Used:
- W11396033
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Frost in bottom freezer, freezer 8%, ice maker works
replaced electric control board, defrost for six hours. next day (24 hours) same problem, [email protected]
Was this instruction helpful to you?
Thank you for voting!