AFD2535DEW9 Amana Refrigerator - Instructions

Old gasket was pulled off with ease. New gasket came folded in-half in cardboard box and was flattened in several places. It was reshaped with ease with the heat from ny wife's hair dryer. Insrallatint took about 5 minutes and seal was perfect. Took less than 15 minutes total.

Easy repair. Unwrapped the new cover; pulled the old one off by releasing tabs. Inserted new piece.
Took less than 15 minutes. Looks like new. The replacement part arrived quickly from Part Select.

Just replaced the switch, but unfortunately that was not the problem; nor was it the bulb....so I am back to square one.
But Parts Select is a great place to order from. Thank you.

Removed the top door hinge cover.
Remover the four 12mm hex screws.
Lifted empty door off bottem hinge support.
Removed old door closure.
Put some silicon lub on the new closure and installed.
Reversed the removal steps.

But this did not fix the problem. Will have to remove the door and inspect the inside of the door's lower hinge assembly.

pop open, unscrew quarter turn, screw new one in quarter turn, pop shut. duh

Very simple. Matched female plugs with respective male color coded prong; pushed together then inserted unit in slot of freezer sidewall and rotated into position...job done.

followed the instructions provided and that's it!

Removed broken lid and snapped new one in place.

I bought a set of appliances used online and the fridge door did not align to the other door. I quickly noticed I had lost the lower bushing to the right door upon transportation so I did what any man would do...find a way to fix it! after checking out a few websites I ran accross Partselect and after seeing their "dummy proof" diagrams It was certain I couldn't mess this up considering the loads of bushings to choose from. The order was placed Monday morning and to my surprise I had a package the VERY NEXT DAY!! AMAZING delivery time and quality products. PartSelect is definately my appliace parts source from now on! Thank you!

Icecubes came out half-way, and refrooze. I figured out, that the melter does not work (HEATER in the icemaker) Voltage measured 105V no load. Studied the Internet, and folloved an advice: shorted the back wire and the blackwire with white stripes.these go to relay contacts. It seems, that the relay contacts are no good on Infrared receiver boaed. I turn off manually the icemaker, when needed

First I removed the six screws from the cover. I then disconnected the two wires and pulled the small motor out with its base and removed two screws that hold it in place. I then changed the old one for the new one and set it back in its place. I then set the cover back and turned it on. I was happy again.

The other instructions and the video provided by Parts Direct are pretty good with instructions, but they omit two steps. First, if you have an ice maker, you will need to unplug the connector on the back side of the panel you remove at the back of the refrigerator to access the drain tube. Just unplug it and you can move the removed panel to the side without disconnecting any of the water lines. Second, the instructions say to just reconnect the "bottom end" of the new p-trap drain to the drain pan at the bottom of the refrigerator. They don't tell you there are two places to connect the new p-trap to the drain pan. The original tube/trough connected to the one at the back of the drain pan on the left (viewed from the rear of the refrigerator). At first, it looks like the new p-trap won't reach to it for the connection, but if you look closer, there is another connector to the right of the original one that the p-trap connects to properly. Replacing the drain trough with the new p-trap was actually pretty easy and would only take about a half hour. Add another half hour to give the refrigerator coils a good cleaning as they will need it now that you can reach them. The real time consumer, 3 to 4 hours, is needed to use a hair dryer to melt and clear the ice from the condenser at the back of the freezer so the water can drain. Just take your time and all the ice will eventually melt and drain out so the new p-trap will work properly.

I called the installer of my filter unit and he told me that often, thhe fridge filter is the problem. Like magic it worked

These guys had my part mailed in lighting fast! It arrived in 2 days in a padded box in perfect shape.The price was the best on line and they saved my life one day before thansgiving!! They got my vote and respect! Great job partselect!!! walt , crete illinois

Watched installation Video on the website parts. I put the new gaskets in bath tube in warm water for a few minuets until the gaskets were warm and pliable. I removed old gaskets cleaned door facing and installed new gaskets as instructed on video. Thanks for the information on how to install because I was dreading trying to do this task. "Just follow and listen to the instruction on Video".