AFI2538AEB4 Amana Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Doug from PLEASANT VIEW, TN
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light switch in freezer side got broken
Took a putty knife and
Removed the old switch removed the spade terminals from the old switch and replaced them on the new switch and just pushed the new switch back in place
Removed the old switch removed the spade terminals from the old switch and replaced them on the new switch and just pushed the new switch back in place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mike from holly springs, NC
- Parts Used:
- M1205302, WP10450603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Left front plastic wheel was broken
Pop loose the plastic grate at the bottom.
Locate and remove the wheel leveling screw from the front bottom corner.
Remove cotter pin from the pin that mounts the wheel assembly to the refrigerator. Tap out the mounting pin.
Lift out the wheel assembly.
Remove the Roller pin from the wheel assembly. I used a Dremel tool with a cutting disk. A hack saw will also probably work.
Install the new roller pin and wheel into the wheel assembly. Use a hammer or vice to peen over the end of the roller pin.
Reinstall and adjust wheel assembly.
Locate and remove the wheel leveling screw from the front bottom corner.
Remove cotter pin from the pin that mounts the wheel assembly to the refrigerator. Tap out the mounting pin.
Lift out the wheel assembly.
Remove the Roller pin from the wheel assembly. I used a Dremel tool with a cutting disk. A hack saw will also probably work.
Install the new roller pin and wheel into the wheel assembly. Use a hammer or vice to peen over the end of the roller pin.
Reinstall and adjust wheel assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Long Valley, NJ
- Parts Used:
- EDR4RXD1
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Six months in use time to replace the filter
It is simple, unscrew the old screw in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phil from GREENFIELD, IN
- Parts Used:
- W11395888
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Remove the water filter to install the bypass cap
Lower the filter bottom housing to gain access to the filter. Unscrew the filter and install the bypass cap. Secure the lower filter housing to the top assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Angela from Bay Village, OH
- Parts Used:
- W10827015
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Cracked plastic on pantry drawer lid
Broken lid popped out, new lid popped in. No tools required. 30 seconds to replace. Great price, part shipped within an hour of placing my order and arrived the next day, although I only paid for standard shipping. Excellent service - will definitely order again if the opportunity arises!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from OLD SAYBROOK, CT
- Parts Used:
- WP13005701B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
No Water or ice would dispense
Had the problem about 3 years ago the fridge was old and I decided to open it up(remove spill tray, detach 2 screws, remove display panel by popping bottom corners and lifting, disconnect 3 wire plug connections, remove 2 screws holding chute assembly) and take a look I found the problem was with the lever running over the switch and that it was worn down not making enough contact to the switch assembly and wrapped some teflon tape around the leverI got 3 years more out of it... this time it was just simply age and needed a new assembly. Again I removed the display panel undid all 3 wire connections along with the water hose. Plugged everything into the new assembly reattached the electronics wires(3) screwed everything back where it was... Done! about 15-20 minutes at most.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Murphy, NC
- Parts Used:
- WP67003639
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Right hand door would not auto close.
Removed the top door hinge cover.
Remover the four 12mm hex screws.
Lifted empty door off bottem hinge support.
Removed old door closure.
Put some silicon lub on the new closure and installed.
Reversed the removal steps.
But this did not fix the problem. Will have to remove the door and inspect the inside of the door's lower hinge assembly.
Remover the four 12mm hex screws.
Lifted empty door off bottem hinge support.
Removed old door closure.
Put some silicon lub on the new closure and installed.
Reversed the removal steps.
But this did not fix the problem. Will have to remove the door and inspect the inside of the door's lower hinge assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gene from Petaluma, CA
- Parts Used:
- W10827015
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
A friend dropped a jar of relish on the plastic window and cracked it.
Easy repair. Unwrapped the new cover; pulled the old one off by releasing tabs. Inserted new piece.
Took less than 15 minutes. Looks like new. The replacement part arrived quickly from Part Select.
Took less than 15 minutes. Looks like new. The replacement part arrived quickly from Part Select.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brenda from Spokane Valley, WA
- Parts Used:
- EDR4RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace water filter
pop open, unscrew quarter turn, screw new one in quarter turn, pop shut. duh
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rolf from Stanhope, NJ
- Parts Used:
- W10827015
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken drawer lid
Removed broken lid and snapped new one in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from West Warwick, RI
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken light switch
followed the instructions provided and that's it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from INVERNESS, IL
- Parts Used:
- 8201515
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Icemaker Would Not Produce Ice
Contacted sears home service to perform repair. Quote for repair was $307. 43. ( $196. 90 For labor ,$102. 58 For part) plus $75. 00 For service call. Based on the charge, I refused the repair and ordered the appropriate part from "part select" (733947) (wpl 8201515) motor module for a cost of $81. 84. To my surprise, the part arrived the next day and in 15 minutes the icemaker was in a position to make ice, and has been producing ice ever since. To perform the module replacement, I had to remove one screw with a nutdriver, pull the icemaker out, disconnect a wire harness, replace the module and do the reverse procedure to complete the installation. I saved a total of $225. 59 By doing this repair myself. A lesson learned. . . . . I will always investigate doing a repair myself with the help from the people at part select. Very professional and they sent the correct part the first time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Newton Grove, NC
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light switch rocker broke, disabling freezer internal light, water dispenser, and ice dispenser
Very simple. Matched female plugs with respective male color coded prong; pushed together then inserted unit in slot of freezer sidewall and rotated into position...job done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Rocky River, OH
- Parts Used:
- WP627985
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
replacing thermostat did not help
Icecubes came out half-way, and refrooze. I figured out, that the melter does not work (HEATER in the icemaker) Voltage measured 105V no load. Studied the Internet, and folloved an advice: shorted the back wire and the blackwire with white stripes.these go to relay contacts. It seems, that the relay contacts are no good on Infrared receiver boaed. I turn off manually the icemaker, when needed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carlos from Streamwood, IL
- Parts Used:
- WP67003639
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door bushing
I bought a set of appliances used online and the fridge door did not align to the other door. I quickly noticed I had lost the lower bushing to the right door upon transportation so I did what any man would do...find a way to fix it! after checking out a few websites I ran accross Partselect and after seeing their "dummy proof" diagrams It was certain I couldn't mess this up considering the loads of bushings to choose from. The order was placed Monday morning and to my surprise I had a package the VERY NEXT DAY!! AMAZING delivery time and quality products. PartSelect is definately my appliace parts source from now on! Thank you!
Was this instruction helpful to you?
Thank you for voting!