ASD2620HRS Amana Refrigerator - Instructions

There is a plastic flapper valve that is spring-loaded in the closed position that prevents ambient room air from entering the freezer compartment via the ice chute. The Ice Chute Seal is a simple flexible (rubber-like) disk that just slips over the circular flapper valve. With the freezer door open one can see the flapper valve down the ice chute and one can reach it easily from the outside of the freezer as well. The Ice Chute Seal has 3 notches that make it very easy to remove the old seal and replace it with the new seal. This can be done by feel. I removed the old seal by pushing the flapper valve open with one hand (from the inside of the freezer door) and could then peel off the seal surrounding the flapper valve with the other hand. Once the old seal was removed I slipped the new seal around the flapper valve. No tools required, no screws needed to be removed. The problem I had with frost/ice build-up was solved; there is no more ice/frost build-up inside the freezer near the top of the ice chute. The old seal LOOKED OK but was obviously a bit too stiff to seal the opening against the warm, moist, ambient room air. I was most happy to see that this solved the problem and that it was so easy to do (really less than a minute or two!).

The Condenser Fan Motor was already removed due to searching for the problem. The new fan motor looked different from the original but I felt very comfortable that Part Select had sent me the new part showing original part number changing numbers over the years. Simply placed the fan blades onto the new motor lined up 2 of the holes placed screws and tightened then plugged the wire ribbon into the Condensor Fan Motor, plugged in the Refridgerator and it worked beautifully.

The instruction video on the Part Select Web Site made it so incredibly easy to install. Installation took under 3 minutes!

Just plugged it in

Bought new cap.

Followed directions on filter unit

Open and remove lower cover on filter holder by opening tabs that hold lower cover and remove lower cover.

Firmly hold back of unit and firmly hold and turn filter in counter clockwise to unlock and remove.

Install new filter by holdin back of unit and install new filter by turning in clock wise direction and then replace lower cover.

Take out the elbow fill tube and check to see if ice build up inside tube. Clean tube of ice build up. Replace tube back in. In my case that corrected my problem.

Popped out the old switch and replaced it with the one dying

Removed the fridge waterline from the main line using the adjustable wrench, pulled the waterlines from their brackets and removed the water filter cover. Once that was done just pulled out the old filter head and waterlines and reinstalled. Hardest part was putting the filter cover back on. Needed smaller hands.

The ice to the door has not worked for the last 2 years. My wife complained about not having crushed ice to drink with. We looked at buying a new refrigerator. I went back online to look for the broken part again (I have looked in the past but never found the part). I stumbled on this website and found the part and it was only $4.00 and change. Only needed 10 minutes and my hands to snap the part in place. I do need a new ice bucket but it works for now and my wife is happy.

This is the 3rd time this has happened since we bought our refrigerator. I always buy the replacement from www. Partselect. Com they make it so easy to look up using the pictures. I love it! Thanks, parts select!

Repair was tremendously easy. All I did was remove old light switch by prying out with screw driver and plugging in the new light switch and pushing it into the hole. Simple! The instructions weren't needed, but they were very thorough.

I popped out the old switch with a screwdriver pressing down the tab on the bottom and unplugged the terminals. Then I plugged in the new switch and popped back into the socket. Piece of cake!

While trying to fix this problem, I spent around $100.00 on a new ice maker (not the problem), $250.00 for a professional to try to fix the problem, and another $60.00 on the dual water valve (not the problem). At the end of the day the problem turned out to be the 10" water line coming into the freezer was freezing solid. I would previously use a hair drier to heat the line and remove a 4" cylinder of ice from the line which I thought was clearing it, but in reality the line needs to be pulled out of the back of the refrigerator so you can just rest it in a bowl of hot water to remove the ice. I spent a good amount of money on this job and have learned to fix everything myself moving forward. The install of the water valve was simple and required just pulling the lines out of the old valve and pushing them into the new valve. Be sure to have a bowl to allow the lines to drain into, and turn off the water supply to the fridge. By the way no amount of googling my problem yielded advice on pulling the water line out the back of the fridge to remove the ice : (

The repair is easy all you have to do is follow the simple instructions posted by the other people and or watch the video by PartSelect. I want to thank PartSelect for being the best company that I have done business with ever. They have restored my faith in honest companies and their service is the best.