AS2628HEKB0 Amana Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Marybeth from VACAVILLE, CA
- Parts Used:
- W11395888
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lost cap for filter
Bought new cap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kerry from DE PERE, WI
- Parts Used:
- WPD7749401
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
End Cap was broken and ice would not dispense.
Ridiculous how easy it was, REALLY!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from TUCSON, AZ
- Parts Used:
- WP12665101
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Frost and ice was building up on the top of the ice chute inside the freezer
There is a plastic flapper valve that is spring-loaded in the closed position that prevents ambient room air from entering the freezer compartment via the ice chute. The Ice Chute Seal is a simple flexible (rubber-like) disk that just slips over the circular flapper valve. With the freezer door open one can see the flapper valve down the ice chute and one can reach it easily from the outside of the freezer as well. The Ice Chute Seal has 3 notches that make it very easy to remove the old seal and replace it with the new seal. This can be done by feel. I removed the old seal by pushing the flapper valve open with one hand (from the inside of the freezer door) and could then peel off the seal surrounding the flapper valve with the other hand. Once the old seal was removed I slipped the new seal around the flapper valve. No tools required, no screws needed to be removed. The problem I had with frost/ice build-up was solved; there is no more ice/frost build-up inside the freezer near the top of the ice chute. The old seal LOOKED OK but was obviously a bit too stiff to seal the opening against the warm, moist, ambient room air. I was most happy to see that this solved the problem and that it was so easy to do (really less than a minute or two!).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debbie from Overland Park, KS
- Parts Used:
- WP67005959, WPD7749401
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice maker would jam up and not let ice out thru dispencer .
Super fast , I received my parts the very next day ,THANKS to PartSelect.com. GREAT JOB .
Pulled out 4 screws , pulled out the ice turn gear & crusher , replaced the helix end cap , put all these parts back in place , screwed 4 screws back in ice bucket , back in freezer and it works like new . It would of cost me $110.00 to have a repair company do this simple job .
Pulled out 4 screws , pulled out the ice turn gear & crusher , replaced the helix end cap , put all these parts back in place , screwed 4 screws back in ice bucket , back in freezer and it works like new . It would of cost me $110.00 to have a repair company do this simple job .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from pleasant grove, UT
- Parts Used:
- WP67002052
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
crushed ice wheel broken
very easy, with use of screwdriver and 1/4 in nut driver. just remember the way the blades go and get them back the same way. had it fixed in 15 mins.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Lemon Grove, CA
- Parts Used:
- WP67002052
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
The wheel broke in half.
Remove ice tray from freeze. Removed all screws, replaced wheel. Reassembled unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Cape Coral, FL
- Parts Used:
- WP12562701
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
broken ice at the door trap door
The ice to the door has not worked for the last 2 years. My wife complained about not having crushed ice to drink with. We looked at buying a new refrigerator. I went back online to look for the broken part again (I have looked in the past but never found the part). I stumbled on this website and found the part and it was only $4.00 and change. Only needed 10 minutes and my hands to snap the part in place. I do need a new ice bucket but it works for now and my wife is happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RALPH from PARAMUS, NJ
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Refrigerator lamp not functioning
Had to push the light switch to get lamp to light up.
Removed power from refrig. and removed old light switch
and replaced with the one I got from Partselect. Turned power back on and was done.
Removed power from refrig. and removed old light switch
and replaced with the one I got from Partselect. Turned power back on and was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jesse from Slidell, LA
- Parts Used:
- WPD7749401
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
not distributing ice
1. Removed ice maker from frig.
2. Emptied all ice cubes.
3. Let it warm up to room temperature.
4. Removed front cover from bottom up (unsnapped).
5. Removed 4 screws.
6. Removed old helix cap.
7. Installed new helix cap.
8. Reverse of step 5 to step 1 above.
2. Emptied all ice cubes.
3. Let it warm up to room temperature.
4. Removed front cover from bottom up (unsnapped).
5. Removed 4 screws.
6. Removed old helix cap.
7. Installed new helix cap.
8. Reverse of step 5 to step 1 above.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Murrieta, CA
- Parts Used:
- W11291138
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light switch broke
I popped out the old switch with a screwdriver pressing down the tab on the bottom and unplugged the terminals. Then I plugged in the new switch and popped back into the socket. Piece of cake!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Zachary, LA
- Parts Used:
- 67002957
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dairy door was cracked
Remove all door. Snap in new door. No tools required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Claude J from Orange Park, FL
- Parts Used:
- WP12603701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Grand child stood on crisper and broke it. Does any one know if a dishwasher front can be changed after it has been purchased,and where you finde it ?
Ordered from P S and very fast service customer service was great. I would recomend P S to anyone that needs parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from LaPlace, LA
- Parts Used:
- WPD7749401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice Maker Auger Jambed and Broke Helix
Removed 6 screws total and removed the entire Auger and Ice Crusher. The broken Helix just fell off, I put the new one on after a little finagaling to get it lined up right and it just snap into place. Replace the screws, put the bucket back, dumped in the Ice and the dispenser started working Fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Justin from Huntersville, NC
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light hinge broke
Repair was tremendously easy. All I did was remove old light switch by prying out with screw driver and plugging in the new light switch and pushing it into the hole. Simple! The instructions weren't needed, but they were very thorough.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Discovery Bay, CA
- Parts Used:
- WP2182124
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
The ice stripper cracked from freezing.
There was three screws to remove to unmout the ice maker, and unplug the wire harness,then two to remove to slip in new stripper. All took about 20 mins.
Was this instruction helpful to you?
Thank you for voting!