SZD20KP (P1102506W) Amana Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Steven from Cisco, TX
- Parts Used:
- WPW10245167
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Ice maker not getting water (1 of 2 step troubleshooting)
Removed water inlet solenoids screws on base and pulled it out about 6 inches; removed 4 tubing nuts. Replaced unit with new and replaced tubing and base. This did not solve the problem so I ordered ice maker unit. Should of checked the inside of the ice maker ias the protective coating was pretty much history so I would ordered it first, and then ordered the inlet valve.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jon from Butler, PA
- Parts Used:
- R0181181
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Bottom Cam broke on Fridge Door
Removed top hinge cover and socketed out hinge nuts. Lifted door off bottom hinge. Socketed out broken bottom cam and replaced with new. Reset door with someone lifting and the other guiding. Reattached top hinge and cover. Voila.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Roseville, CA
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door light switch disintegrated
Very simple fix, remove 3 screws, two connectors to the old switch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Strongsville, OH
- Parts Used:
- 67003696
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
None
My wife just snapped it in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yafa (and David) from Bothell, WA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Replacing the bulb in the freezer side
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stu from richmond, VA
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
fridge door switch did not work
I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!
Why didn't I order this part and do the repair earlier? Very simple.
Why didn't I order this part and do the repair earlier? Very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lyle from Bismarck, ND
- Parts Used:
- WPW10245167
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Ice maker stopped making ice
I removed the screws on the back of the refrigerator revealing the water valve, disconnected the water supply, removed the two outlet hoses and removed the bad valve. Replaced in the opposite manner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from JACKSON, WY
- Parts Used:
- R0181181
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
door closure part broken. door wouldn't remained closed
removed door.examined problem,. installed part. super easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anders from Eagan, MN
- Parts Used:
- WPD7872801
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Defroster heater coil broken
Removed covers. Lifted and angled out the freezer unit. Removed clips at bottom and pulled out the heater coil. Threaded the new coil in place and replaced the clips. Lifted and hung freezer unit back in place. Re-connected wires and turned on the fridge. Verified that fan worked when cooled down and defrosted at end of cycle. Replaced the covers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- craig from maple grove, MN
- Parts Used:
- 833697
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
noisy fridge, perimeter of door heating up
figured out the condenser fan was kaput. Tried WD, worked for several days then gave out completely. Took off back of fridge and trained small fan on compressor while I ordered new condenser fan. The swap was easy, undid the housing bolts, stripped off the connector, reconnected and voila! works perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- christopher from colfax, CA
- Parts Used:
- WPW10245167
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
split/cracked water solenoid valve
very easy. removed the old solenoid because it was cracked and spraying water all over the floor. installed the new part, turned on water supply and that was it!! water dispenser in the door works better, it fills a glass faster and the ice maker works better too.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Granada Hills, CA
- Parts Used:
- 833697
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
refrigerator was overheating, condensor fan dead.
First I removed all the screws from the back cover.
2nd removed fan nut and fan blade
3rd removed fan bracket
4th I traced wire to the condenser and disconnected wires from wire nuts.
Installed existing fan brackets to new motor kit
then reconnected wire nuts to new motor cord
Reinstalled fan nut and blade,
reinstalled cover, plugged it in and BAM .WORKS PERF!
2nd removed fan nut and fan blade
3rd removed fan bracket
4th I traced wire to the condenser and disconnected wires from wire nuts.
Installed existing fan brackets to new motor kit
then reconnected wire nuts to new motor cord
Reinstalled fan nut and blade,
reinstalled cover, plugged it in and BAM .WORKS PERF!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leonard from Leitar, NM
- Parts Used:
- WPW10245167
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Dripping water from despenser
Moved frig away from wall, unpluged and took off lower back panel. Disconnected water line and ice maker lines from water valve (after shutting water off). Removed 2 screws, New valve was exact replacement. With new valve in hand, I removed electrical connecters one at a time and placed them on new valve. Put new valve in place, inserted 2 screws and tightened, Connected water lines, checked for leaks, moved frig back in place, job complete. No more drips, worked perfect. Total time, about 30 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerald from San Antonio, TX
- Parts Used:
- WPW10245167
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Broken water inlet valve.
I removed the back cover, disconnected the water line from the valve and unplugged the wires. I went to the Parts Select website and entered the info on the part (Plastic, Electrical) and brought up several beautiful pictures that immediately allowed me to identify and order the part without ANY part or model numbers! Wonderful! 3 days later, I installed the part in reverse order and the icemaker works like new again. Thanks for making it so easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Minneola, FL
- Parts Used:
- R0181181
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
The fridge lower hinge mechanism which assists door closing broke
Removed the top hinge cover with Philips screwdriver. Removed the three bolts holding the top hinge in place. Removed the top hinge, and lifted the door off the remains of the lower hinge. Unbolted the remnants of the lower hinge closure mechanism and replaced it with the new set. Reassembled the door on the lower hinge, and then replaced and bolted back on the top hinge. Door back to full working order in less than fifteen minutes.
Was this instruction helpful to you?
Thank you for voting!