XRSS204BW (PXRSS204BW0) Amana Refrigerator - Instructions

Took knife and pried out the the damaged switch. Took wires off. Put the wires on the new switch and put it back in the hole. Job finished. The part shipment was very prompt and I am happy. The End!

Recently unemployed, we knew a repairman was out of the question. We opted to glue the broken tab,but I knew that would just be living a substandard rerpair so looked on line. Found our replacement part very easily and much to our surprise we had the part the next day, yes, the next day!! Looking at the new part gave us the confidence to pop out the old one without causing damage to our unit. It was a no brainer , pop out and plug in w/in 30 seconds. Small appliance repairmen are a minumum of 75.00 service fee plus parts. Our repair less than 20.00 less than 24 hrs. How good is that?

Gail Costa

Within a 2 months of purchase the compressor on This refrigerator this unit failed. and again two years later. After all of that, we were pleased to find a replacement dairy door for this unit. thank you!

Popped old one out with knife. exchanged power leads. Popped new switch in. Make sure to unplug refrigerator before you start!

I removed the old bins, making sure to get all the pieces that had broken from the back tabs where they slide into the upper support racks. The replacement bins slid in easily and work perfectly.

I popped the switched out depressing the underside of the switch so that it could be removed.
I ordered the part.
Paid for normal shipping.
Received an order confirmation.
Received a shipping notification.
Received the part the next morning.
Open the part and attached the wires.
Pushed the switch into the hole and the process was done in less than 24 hours. I couldn't have been more pleased. The actual installation took less than 30 seconds.

great service parts arrive quickly

1. Removed part from packaging. 2. Cleaned part with foodsafe cleaners. 3. Rinsed thoroughly. 4. Dried thoroughly to prevent frost. 5. Placed bin in freezer. 6. Turned on ice maker. 7. Waited. 8. Discarded first batch to clear supply line. 9. Waited. 10. Enjoyed ice. 11. Provided these inductions.

The worst part was unloading the door shelves. Removed upper hinge cover and hinge hex screws. This allows the door to be removed. Lay the door on side. Remove screw that holds cam in place. Replace
broken cam with new piece. Put the door back on the hinge pin and replace upper hinge screws and cover.
Now reload all of the stuff.

replaced drain hose; melted ice that had built up behind it

Took the door off, and replaced the plastic shim on the bottom that was the cause of the problem. The shim had broken into pieces and was no longer holding the door in height and alignment. I was proud of myself that I could repair it myself and avoid a $125.00 service call from a repairman. Total cost of repair including shipping and handling was just south of $12.00.

I followed the other web notes with one change .Since I too forgot the lube , I used a pry bar and block of wood to lift the door and a tooth pick to glob some lube in the lower hinge.

Remove the grandkids pictures from the door then empty the contents inside the door. Remove the top hinge cover and the top hinge bracket. Lift the door off the bottom pivot. Replace the lower cam by removing one screw. With the door in the horizontal position, remove and replace the upper cam. Apply a little grease on both cam surfaces. Align the door before tightening the top bracket and your done. If you did not take a picture of the door before you started the project you will have to rely on memory to arrange the pictures in the proper location.

Removed the top hinge (4 screws)-lifted the door off of the lower hinge-replaced both halves of the cam kit and mounted the door and reattached the upper hinge.
Probably took about fifteen minutes total.

Just put the dairy tray were I wanted it. Will do the same with the crisper drawer when it arrives.