ASD2324HEQ Amana Refrigerator - Instructions

Removed back access cover with quarter inch nut driver, unplugged wire harness, pulled old relay out & plugged in new one, reconnected wire harness, and reinstalled access cover. Piece of cake. (Shipping was very quick) ***Frig was only 3yr an 1 mounth old.*** Maytag - Dependable Huh?

While investigating problem (at 11:30PM of course) I saw the overload burst into flames. Problem Identified! Easily found and ordered part. Next day delivery. Exact same part easily plugged in. Total refrigerator down time was less than 40 hrs.

Thanks,
Terry

Once I got the right part the repair was quick and easy. All I had to do is get the old part off with a screwdriver and curved needle nose pliers and the old part came right off. The new part went in just as easy. Quick and easy. Less than 15 minutes.

Received the union I ordered, then discovered that the tubes were different sizes, so I had the wrong part. I had read elsewhere that it was necessary to trim the two ends of the tubes with a box cutter to stop the leaks - I did this, and the leaking stopped. I was then able to go to a local hardware store and get a 5/16 to 1/4 union and replace it. The leaking is stopped, and the water supply in the door is now working like new. No problem with partselect, but I did buy a caliper so that I can check tube diameters if I ever have a similar problem! This is a great site to find instructions - well worth the time to search!

Looked on web to see problems with same model. Recieved new board, unplugged fridge,took off cover inside fridge top left,took old board out, unplugged wires from old board and plugged new board in, installed cover and plugged fridge into wall outlet.

Had to disassemble ice maker to install part. . .

While ordering the assembly, I had thought that the ice bucket was included but it wasn't. So I ordered the ice bucket afterwards. Maybe a little more clarity as far as what parts come in the whole assembly would save some time. All in all, the agitator was very easy to install, along with the ice bucket. After securing the agitator to the existing assembly with two screws, the ice bucket slipped right into place. Easy to install.

As the prior stories mentioned, this was a fairly easy fix to a nagging problem. Heck, we almost bought a new refer over this, cuz the door would keep popping open.

Needed a screwdriver, and a 5/16" nut driver (mounted in elec. drill). Have two people for this one! Emptying the door would help out tons too. ('course, I didn't do that!)

With the door closed, remove the plastic cover on top by removing 1 phyllips screw. Then, using drill mounted 5/16" nut driver, remove 3 hinge screws. Remove hing by lifting up. Now, carefully open and remove the door. Here is where the 2nd person comes in. There are 2-3 1/4" screws (Must use a 1/4' NUT DRIVER, SOCKET OR MAGNETIC BIT HOLDER) on the bottom of the door to remove the broken plastic cam. Also, you must remove the bad cam from the bottom hinge using I believe the 1/4" nut driver.

Finally , one person lift the door while the other kneels on the floor to help giude the door back onto the bottom hing pin. Close the door, ensuring that the top of the doors are even, and secure the 3 top hinge screws. UR done!

Greg

Followed the YouTube video linked to the Compressor Start Device and Capacitor I purchased. The repair was just as easy as the technician in the video said it would be. Removed the back panel, remove the clamp, worked the Compressor Start Device and Capacitor off the electrical prongs and replace it with the new one. After I reassemble the refrigerator, it was fully operational. Very easy to do and only required a few tools.

Well folks I put up with an ice burg all summer when I really should have took the time to fix it. You know how it goes though. You get so busy you just put it off.
Well don't put this one off because this is just how easy it went.
I came home one evening and wanted to make a drink to relax but that big glob of ice was there waiting for me. I took a crewdriver and beat it down so I could pull the catch basin out. Having looked it over for a minute I grabed a nut driver and took three of the screws out that held it in. I unpluged the wire and bingo it was out. Maybe five min. had elasped.
After taking the unit out I notice how the non stick surface was coming off of the tray and that explains the black pieces that were getting into my ice.
Getting the model number off the back of the fridge and writing it down I went to my trusty lap top and did a quick search for a ice maker for my Jenn Air refrigeraton and blamo...! Part Select came up and I put the part number in their search engine and bingo again there it was, my part.
One quick order and in three days it was right there by my door when I got home.
Now i'm so excited. I went into the house and didn't even chage out of my dress clothes. Within five minutes it was in. Now I just had to wait for the timer to do it's thing and sure enough, I awoke the next morning to a whole tray of beautiful ice cubes. Wow no more ice burgs.
The moral of my story is I spent so much time hacking out that glob of ice and for fifteen minutes of my time, I could have been siping on cold ones by the pool but now old man winter is pressing down on me and I guess a lesson learned was a lesson earned. Fix it!

1 screw remove assembly. Unplug cable harness and remove old cover and wire arm. Replace cover and wire arm and attach wire harness on assembly end. Re attach using screw removed in first step. Plug in wire harness. Making ice within 30 minutes.

By sliding athin screwdriver blade down the side of the old switch the expasion prong that hold the switch in place was compressed enough to allow the switch to come out easlily. Plugged in new swithc and snapped in place. Plugged the refrigerator back in and light has worked great sense!

Diconnecting the hoses was a pain as there are no instructions. Draw a diagram of each hose and color of the connectors or better take a picture before starting. Make sure the water is off, have a bowl & towels ready to mop up the water that runs out of the hoses. You have to push each hose in along with the little top hat connector that the hose runs thru. With both pushed in, hold the top hat connector down and pull the hose up and out. I could not reconnect without a leak on the hose that has a spring in it if I slipped the hose thru the white bracket. I ran the hose outside of the bracket and it went right in with no leak.

I did a few tests with the old ice maker and determined that it was the ice maker itself that was faulty. The replacement part I ordered exceeded my expectations in the time it took to get the part. I reused the arm, wire harness and clamps from the old icemaker. Then it was a simple install into the bottom freezer compartment, turning on the water supply and bingo...lots of ice cubes.

I unhooked the wire harness from the ref. and took out three screws and pulled the old unit out. I than changed a few parts from the old icemaker to the new and reattached the new ice maker to the ref. and plugged the wire back in. everything is working fine. No problems. Also I was very happy with the ordering process. Thank you!!