P1303504WE Amana Refrigerator - Instructions

After I pull out the fridge, turn off and remove the water supply line. I removed the screws that held the water valve in place. Once I pulled the water valve out, I discounted the two internal water lines, (one for the ice cub tray and the water in the door) and then removed the two sets of wires connecting to it. I then replaced the Water Valve, reconnected the two sets of wires, replaced the two internal water lines, as well as the supply line. Srewed the water valve back in and tested the water in the door. Everything worked great.

Philips head screwdriver and ten minutes was all it took! I removed the two screws that hold the icemaker assembly in place, then pulled it out a little and disconnected the electrical plug freeing the icemaker assembly. Then I snapped the external parts off my old icemaker assembly and snapped them on the new icemaker assembly. Installing the new icemaker assembly was just as fast and easy. I snapped the electrical plug into the new icemaker assembly, then screwed in the two screws. It was making ice shortly thereafter. Glob free ice! I'm glad I didn't call a repairman. I probably saved a hundred bucks. A ten year old could accomplish this simple and easy task. No wonder the Maytag repairman has time on his hands.

First of all, I do not have a history of repairing appliances or even the knowledge of what all the parts are named or how it all works. That said, please excuse my other than technical explanation of the repair. After reading a few posts, I decided to order the two parts and give it a try. The Defrost timer was easy to remove - two screws to remove the housing and two screws to remove the timer. The bimetal defrost thermostat was an easy installation - after removing the cover plate (back of freezer section) I removed the two wire caps that was connecting the existing thermostat to whatever it connects to - I guess the heating element and ? I was a little confused because the replacement thermostat had more wires that the existing one. I decided to cut away the extra wires and connect it just like the old one was connected. I didn't work at first and I was about to call in a pro. I turned the defrost timer knob and everything started to work. It has worked beautifully since and I got to brag a little to my wife - that was short lived because she reminded me of the other "stuff" that needed to be fixed! Thanks to the folks that posted before me - it helped me understand the problem and the repair.

After moving the refrigerator away from the wall I removed the cover on the lower back of the unit by removing the screws that held it in place. The condenser fan was not turning and there was heat build up in the area causing the refrigerator to not work properly creating elevated temperatures in both the freezer and regrigerator. Removal of three torx screws from the original motor was all it took to get the motor free. By turining it and working the fan blade around the mounting bracket I had the motor out in just a few minutes. Replacing the new motor was just as easy to reinstall. The fan was removed from the old motor and placed on the new for installation. The original motor was wired to accept a connector from the wiring harness of the refrigerator. I simply cut the connector off the wiring harness and stripped the insulation from the wires which easily allowed me to connet the wires of the motor and harness with two wire nuts. Three self tapping screws were used to hold the motor in place replacing the torx screws. Installed I plugged the unit in and immediately the fan started spinning as the unit came to life. Cleaned and replaced the cover over the back and slid back into its spot. Running as good as it did when it was new. Easy job to take care of.

Water was dripping out of top freezer door and had water under the refridgerator. I could hear a clicking noice from bottom of refrigerator every 3-5 minutes.
After removing back panel, I noticed the fan was running and the clicking seemed to be coming from somewhere around the compressor which was warm. I noticed on the site a simular problem had been submitted. It said to remove the start relay and if it rattled it was bad. I removed two wires from it ( it is connected onto the side of the compressor) then took a small screw driver to pry it away from the compressor. It not only rattled but had tiny pieces falling out. I ordered the part and replaced it in less than 15 minutes total and all is well.

Turned off power to Refrigerator.
1)Removed broken light switch, using a screwdriver, to gently pry it out. Then unlugged the switch from the connector. I used long nosed pliers to gently pull out the connector from inside the frig, so I could easily plug in the new light switch. I then pressed the new light switch back in place.
2) Remove light cover. I then unclipped the socket which holds the light bulb, I gently pulled it out and unplugged it from the two wires. I then attached the two wires onto the new light socket and clipped it back in place. Bingo done with both items practically no time!

I ran all the ice maker module tests that I could find online, I tried cleaning the contacts inside the ice maker control module, nothing worked...so I finally decided to purchase a new control module. I had already had the module out and taken apart a few times, so the new one was very easy to install. Just removed the entire icemaker from the fridge, removed a few screws, took off the old module, put on the new one, replaced the screws, re-installed the icemaker in the fridge (it just slides in and out similar to a shelf). And 30 minutes later I heard the first batch of ice cubes drop! And by morning the bucket was nearly full. After two weeks of no ice and trying to fix it myself - the family was glad to have ice again (it was July in NC!). In retrospect, I should have followed the advice I found online and ordered the new part sooner and saved all of those frustrating hours of trying to "fix" the part myself.

The new Ice Maker Assembly arived in less than 24 hours. I was amazed that it came so fast.

I had already removed the old ice maker in order to get the modle number.

I just took two parts off of the old ice maker and quickly snapped them into place on the new ice maker. Then attached it to the refrigerator in less than 10 minutes. With in a few hours I had ice again !!!!!

I would definatly use partselect.com again.

I determined that the ice maker was not getting any water. There was only one possibilty, the water inlet assembly. I removed the cover on the bottom back side of the fridge, then removed two screws, three water connections by hand, two electrical connections, reversed everything that I had previously done and in about twenty minutes the ice maker had water.

I removed the plastic cover from the top hinge and loosened the screws. The magnet seal kept the door in place so I removed the top hinge and tried to lift the door off the bottom hinge but the water line wouldn't let it go. Since I don't use the water feature, I just cut the water line and lifted the door off. That's when I discovered the hinge pin was actually broken off, not just the cam. I went ahead and replaced the cam kit and put it temporarily back together, got right back on line and ordered the bottom hinge. The service was again very fast and in a couple of days I received the bottom hinge, repeated the whole process again and this time replaced the bottom hinge assembly, put some petrolium jelly on the cam kit and now it works smooth and perfect.

First I removed the knobs, then the plastic cover over the thermostat. Then, I removed the two screws that hold it on. I removed the thermostat, unplugged the electrical leads, and pulled out the old thermostat. I then inserted the new one, hooked up the leads and reassembled.

I pulled the whole unit(condenser&overload relay)
with my hand & disconnected the wire connected
to it & Replaced it with the new one.Peace of cake.

Took longer to move food from door to inside fridge & take grandkids' artwork off door, & then put it all back than it did to replace cam.
1. Used phillips head to undo 1 screw holding cover over top bracket; lifted off cover.
2. No need to have someone hold door while you remove top bracket; magnets in door gasket will hold it tight to fridge. Used socket to remove 3 screws in top bracket & lifted bracket up off top of door.
3. Door's not heavy. I stood on a sturdy chair to get better leverage. Opened the door enough to break the magnetic seal & llfted it up off bottom bracket. I moved it over just enough to get to the cam, rested the bottom of the door on the floor, & leaned it up against the open front of the fridge to help preserve chilled food.
4. Removed the 1 screw holding in the bad cam to the bottom bracket (uses smaller socket than screws on top bracket).
5. I checked part that goes up inside bottom of door & it was fine, so did not replace it.
6. Trickiest part: putting the door back on. I put a hand mirror on floor by the right corner & facing up so I could see the underpart of the door as I lifted it eased it down on the right place.
7. Closed door, made sure it was straight, replaced top hinge & cover, food, & artwork.

the problem was the evaporator has frozen causing the water line to freeze also.
I opened the cover to see the evaporator, verify it was frozen, try to unplug and let it thaw, but it would freeze again. Thought the defrost thermostat was not working but did not verify, order new one and replaced; it did not work. After a long time of experimenting different things I found out that the defrost thermostat was supposed to be clamp to the line. It was not clamped to the line, was just hangin from its wires when I found it. So.....it works now!!! but I don't know what happen in the first place: the clamp fell off, or did it come from mgfr unclamped but happen to work since it was cold new, now getting old and not cold enough to close the thermostat unless on the line? anyway, it works and I decided to keep the part for spare. Hope this help someone else!

pull the fridge out away from the wall and hope you have a long flex water supply hose.remove cardboard cover,oh yea unplug fridge first.unplug wire from the relay.flip the wire retainer off the relay and pry it away from the compressor.pull the 2 prong capacitor off and then reverse the steps to reasemble. skip the middle man at the local appliance shop.i waited 2 weeks for him to get the part and gave up.your reg shipping got it here in 2 days.