ABD2233DES Amana Refrigerator - Instructions

Unplugged refrigerator. Removed lower back access panels and panel running up the back of refrigerator. Removed and disconnected old fan. Removed old fan motor from mounting bracket. Removed fan blade from old fan motor and placed on new fan motor. Connected new fan motor to power supply. Tested. Reinstalled.

I removed the back panel. I used my hair dryer to remove the build up ice. Then I removed the old thermostat, spliced the wires to install the new thermostat, and crimped the wires. I saved $150 doing it myself. If you know how to splice and crimp wires, you can do this; even a caveman can do it.

The old icemaker had a bad motor and would stall in the fill cycle causing my kitchen to flood on occasion.

The new one was so quiet, I thought it didn't work!

Anyway, one nutdriver and 5 minutes and I had the new one in there... It is so quiet, and I always have plenty of ice now!!!

Thanks!!!

Followed the first set of instructions from the parts select website. It worked perfectly. Just note that the way to remove the "blue" tube is by pushing down on the fitting and then pull the tube out. Be careful with the styrofoam piece around the hole for the tubes as it can crumble around the edges.

tested bulb good ,replaced door switch first(least expensive)then ordered light socket and circuitboard.If clicking sound is heard replace circuitboard first to save on return shipping because the switch and socket where ok

Gain access to rear of refrigerator. Use protective board to prevent marring floor. Unplug refrigerator. Turn off water supply and depressurize line. Remove old water filter head. Disconnect filter head inlet water supply line located behind the refrigerator. Disconnect the filter head filtered water return line at the water valve. From refrigerator interior, disconnect the lower filter water cover. Press the outer cover away from filter head until one end is free of the water filter head tang and remove cover from second tang. Push the Styrofoam "block fill" toward the rear of the refrigerator to remove it. If you try to remove this from the outside by pulling it, it will likely break. Pull water filter head assembly to remove it. Install new part by reversing the steps.

I was easily able to find the part using the online search. I order the part and it arrived in about two days. Installing the part meant pulling out the two crisper drawers, emptying the shelf above the crispers, removing two glass shelf plates, inserting the new part, replacing the glass plates, replacing the food on the shelf and sliding in the two crisper drawers. All in all, about 3 minutes.

Removed the filter from inside the ref then disconneted the water line to filter and to ice maker on blue line just push line down then up to remove. Then pull whole assb. thru refreg. and install new one. very easy 2nd time mine went bad 1st time it coast almost $300.00 this time less than $50.00. Take your time and its fool proof.

4-Screws 3 plactic hoses to remove pull 3 tubes out and instol new part last then 15 min. Making shure is no leaks. Easy

I called the local Amana repair man, wanted $150 for a new ice maker because they could not get the part I needed. Found Partsselect.com and the part cost $17 with shipping. They saved me over $100. The repair was very easy too, just removed a couple of screws.

Thanks,
Matt

noticed the fridge and frezzer were not cold one day.i got on google and typed in the problem and found out the the relay goes bad rather often. was an easy fix. found the parts here on partselect and recieved in with in 2 days of ordering. pulled the old part out put new part in and plugged fridge in and was back up and running with in minutes..thank you partselect....

I loosened the two top screws, removed the bottom screw, lifted up on ice maker and slid it off, unplugged the wire from refrig. I transfered the wire to the new icemaker, pluged it back in, placed it on the two screws, installed lower screw, tighten top screws. Total time spent less than 15 minutes. The ice maker cost $125.00 with freight. Sears wanted $374.00

First turned off the water at the valve. Next I undid the 5 screws holding the plate that holds the pump. Next disconnected the power connectors, then the water lines. Next undid the screw holding the pump, removed pump. Next, mounted the new pump to the plate, this was tricky because it has to fit kind of upside down, so you have to wrangle it into the proper position then align the screw hole. Next, secured it to the plate with the screw, re-connected the water lines, then the power. Before mounting it back to the fridge, I tested to see if it worked, well, it didn't. My heart sank. I re-checked all connections, I redid the entire process, disconnected and re-connected and still did not work. I researched the problem online and someone posted maybe the water filter might be clogged or defective. So I removed the water filter and put the stop plug in, and it worked perfectly. I went and exchanged the filter and plugged it in and still had the same problem. I am now suspecting the filter receptacle is the fault, but we will do without that for the time being. But the pressure is much better so changing the pump was still necessary. All in all a very interesting repair. I learned a lot about how the system works and now I need to replace the damper, it is very noisy.

This gasket is just friction fit into a molded groove. Easy to pull out and replace.
When I googled looking for how to.. all sites described unscrewing a keeper. None described that this (and maybe others) simply has the push-in design.

I removed the crisper drawers, glass shelf, and frame assembly to install the ladder hook. Before reinstalling the glass shelf on top of the crisper frame, I installed the center crisper rail.
Thank goodness for websites like this!