ARSE665BS (PARSE665BS1) Amana Refrigerator - Instructions

First I removed the existing copper ice maker line and then installed a plastic line. I then tried the appliance, with no change. I then removed and replace the primary water valve and then tested that as well. There was no change in the outcome. So I removed and replaced the secondary water valve and tested that as well and I noticed a significant change in water pressure, and in volume.

As the prior stories mentioned, this was a fairly easy fix to a nagging problem. Heck, we almost bought a new refer over this, cuz the door would keep popping open.

Needed a screwdriver, and a 5/16" nut driver (mounted in elec. drill). Have two people for this one! Emptying the door would help out tons too. ('course, I didn't do that!)

With the door closed, remove the plastic cover on top by removing 1 phyllips screw. Then, using drill mounted 5/16" nut driver, remove 3 hinge screws. Remove hing by lifting up. Now, carefully open and remove the door. Here is where the 2nd person comes in. There are 2-3 1/4" screws (Must use a 1/4' NUT DRIVER, SOCKET OR MAGNETIC BIT HOLDER) on the bottom of the door to remove the broken plastic cam. Also, you must remove the bad cam from the bottom hinge using I believe the 1/4" nut driver.

Finally , one person lift the door while the other kneels on the floor to help giude the door back onto the bottom hing pin. Close the door, ensuring that the top of the doors are even, and secure the 3 top hinge screws. UR done!

Greg

The other guy described it perfectly so all I can add is that this repair was as simple as they come. Don't hesitate.

1 - Look at the schematic for the "Fountain" on Partselect.com
2 -Order the ice chute door and seal (seal is rubber and eventually it will stop sealing - while you are in there go ahead and change it)
3 - Unplug the refrigerator then remove the sump tray by pulling it straight out from the door
4 - Unscrew the two screws hidden behind the sump tray - hold the dispenser front housing in place so it doesn't drop downward - after removing the two screws slide the dispenser front housing downward while pressing it against the refrigerator door - there are two clips on the back of the housing that hold it against the refrigerator door
5 - Gently pull the dispenser front housing out of the refrigerator door an inch or two - you will be able to see the electrical connections between the dispenser front housing and the refrigerator.
6 - Continue pulling out the dispenser front housing until you can reach the multi-wire connector on the left - the connector is held together by a clip on the bottom center - squeeze the clip at the end closest to the wires to release it - gently pull the connector off
7 - In the center of the back of the dispenser front housing is a black plastic box (the limit switch) - again, gently pull it away from the two clips holing it on
8 - Set the dispenser front housing aside
9 - Slip the water hose out of the clips holding to to the chute
10 - Unscrew the three screws holding the chute to the door (two on the left and one on the upper right - Slide the chute out of the door
11 - Hold the door hinge so you don't accidentally break it (personal experience) and unclip the top then the bottom of the ice cube door from the hinge (the ice chute seal and ice chute door insulation are attached to the ice cube door - take all three out at the same time)
12 - Slip the ice chute seal off of the ice cube door - pull the ice chute door insulation out of the ice cube door
13 - Put the ice chute door insulation into the new ice chute door - Slip the ice chute seal onto the ice cube door (the schematic will give you the proper orientation for all of the parts)
14 - Again holding the door hinge - slip the two "L" shaped clips onto the bottom of the ice chute door - rotate the ice chute door assembly and snap (gently) the two side clips into place over the opening in the door hinge
15 - Breath a breath of relief if you didn't break anything
16 - Slide the chute assembly over the white pin on the lower right of the refrigerator opening that accepts the chute
17 - Replace the three screws that hold the chute assembly to the door - replace the water line
18 - Clip the limit switch onto the back of the dispenser front housing
19 - run the multi-wire connector behind the water line - connect it to the back of the dispenser front housing
20 - Slip the wires back into the clips along the sides of the opening in the refrigerate door
21 - Rest the dispenser front housing on the bottom of the door opening - it must fit flush to the door (top, bottom and sides) - Slide it gently upward until it stops - replace the two screws at the bottom rear of the dispenser front housing - slide the sump tray back in place
22 - Plug in the refrigerator
23 - Dispense ice cubes into a high ball glass and enjoy a job well done

turn off water and unplug fridge. remove ice maker bottom mounting screw. just loosen the 2 top mounting screws. unplug wire harness from back of fridge. remove old icemaker from freezer compartment. once removed, salvage square endcover and reinstall on new maker. unfasten wire harness from old maker and reinsatll on new one. reinsert thermal wire in new ice maker holding bracket. remove second wiring bracket and reinstall on new maker to hold remaining wires (not mentioned on "how to-" video). remove old ice maker on/off bale and reinstall on new one. remount new maker to top mounting screws, reinsert harness plug into fridge. replace bottom screw,

Well folks I put up with an ice burg all summer when I really should have took the time to fix it. You know how it goes though. You get so busy you just put it off.
Well don't put this one off because this is just how easy it went.
I came home one evening and wanted to make a drink to relax but that big glob of ice was there waiting for me. I took a crewdriver and beat it down so I could pull the catch basin out. Having looked it over for a minute I grabed a nut driver and took three of the screws out that held it in. I unpluged the wire and bingo it was out. Maybe five min. had elasped.
After taking the unit out I notice how the non stick surface was coming off of the tray and that explains the black pieces that were getting into my ice.
Getting the model number off the back of the fridge and writing it down I went to my trusty lap top and did a quick search for a ice maker for my Jenn Air refrigeraton and blamo...! Part Select came up and I put the part number in their search engine and bingo again there it was, my part.
One quick order and in three days it was right there by my door when I got home.
Now i'm so excited. I went into the house and didn't even chage out of my dress clothes. Within five minutes it was in. Now I just had to wait for the timer to do it's thing and sure enough, I awoke the next morning to a whole tray of beautiful ice cubes. Wow no more ice burgs.
The moral of my story is I spent so much time hacking out that glob of ice and for fifteen minutes of my time, I could have been siping on cold ones by the pool but now old man winter is pressing down on me and I guess a lesson learned was a lesson earned. Fix it!

1 screw remove assembly. Unplug cable harness and remove old cover and wire arm. Replace cover and wire arm and attach wire harness on assembly end. Re attach using screw removed in first step. Plug in wire harness. Making ice within 30 minutes.

remove front grill. with pry bar and wooden block, elevate side with broken wheel and insert wooden block behind assemble from the exterior bottom. With roller wheel assemble lose from the wooden block remove front elevator screw from the front frame. next remove cotter pin with the pliers and pull assemble pin. next elevate assemble out. drill out axle on the crimp side insert from the hardware store one 5/16 x 21/2 bolt with nut and new wheel. reinsert assemble in the reverse order. Remove wooden block and adjust height of wheel. replace grill. job complete. good job

By sliding athin screwdriver blade down the side of the old switch the expasion prong that hold the switch in place was compressed enough to allow the switch to come out easlily. Plugged in new swithc and snapped in place. Plugged the refrigerator back in and light has worked great sense!

First, I removed the bucket and drained all the ice from it. Then I took the ice bucket out and lifted off the cover of it which exposed the teeth that grind up the ice. I then removed these in succession and placed on my table so I could make sure I put back together appropriately. Once I had the bucket with everything off of it, I replaced and threaded the auger back through it so I could attach the end cap to it. Once that was in place, I put the parts back on the way I took them off. It really was a painless process and saved a ton of money versus calling a repair person. Definitely will use the service again. Very prompt delivery as had the parts 2-3 days after ordered. Well done.

I unhooked the wire harness from the ref. and took out three screws and pulled the old unit out. I than changed a few parts from the old icemaker to the new and reattached the new ice maker to the ref. and plugged the wire back in. everything is working fine. No problems. Also I was very happy with the ordering process. Thank you!!

I removed the 5/16 inch hex head nuts holding the rear access panel where the power cord was connected. Once removed, I released the Molex plug and ground wire. I connected the new cord, screwed in the ground and installed the rear panel. Having the exact OEM part made the job quick and easy.

Snapped into place with the attached clips. Could not be easier. Really great service from PartSelect--got here faster than I expected. This was a great service--would recommend to everyone!

I pulled off the plastic shield from the front of the ice bucket. This exposed the two screws that I needed to remove to disassemble the ice crusher mechanism. Once the screws were removed, I was able to remove the helix and replace the end cap that was broken and place it in the new ice bucket. If I would have known it was this easy, I would have changed this out a year ago, instead of doing without crushed ice through the door for so long. Thanks PartSelect. com! I am a customer for life!

I knew it was either the thermostat or defrost control board. Checked resistance with multimeter across the thermostat and heater element. Both check out ok so I replaced the board and all is good. Board on my model was in the controls panel.