TX18VL (P1301702W L) Amana Refrigerator - Instructions

I unhooked the wire harness from the ref. and took out three screws and pulled the old unit out. I than changed a few parts from the old icemaker to the new and reattached the new ice maker to the ref. and plugged the wire back in. everything is working fine. No problems. Also I was very happy with the ordering process. Thank you!!

It was a complete mess and a failure. There were no in structions with the gaskets except warming them in water to streatch them. Nothing with a photo of what the gasket looks like as it is being installed or after installation. I am still not convinced they are the correct gaskets for the model. It was a total waste of time and $130.00 to try to replace the gaskets. In the end, I determined that it would be cheaper in the long run to buy a used refrigerator than to mess with the gaskets.

I didn't. Don't know how to get to light bulb to change it for this specific model

Unscrewed the old handles and replaced the new handles with the same screws... that easy! It was the easiest repair that I ever had to do.

I first loosened all screws that are hidden by seal leading edge. I then removed seal. I made sure that I knew which side of seal was to be in contact with refrigerator door frame to provide the seal. I positioned the seal on the door inner panel starting at the top. After I had finished positioning the top I proceeded to position both sides and then the bottom. I tightened the screws only enough to hold the seal in position. After I had the seal in the proper position I tightened the screws that hold the seal in position. I used a hair dryer to heat seal and smooth out the the sealing edge.

Replaced refrigerator cooling control. No luck. Replaced freezer cooling control. No luck. Coils were icing up. Unplugged frig and allowed coils to defrost. After more poking around, found that condenser fan was not spinning. Touch it and it'd start. That was definitely in need of replacement. Replacement was easy. Refrigerator is now running as it should.

Took out three screws, kept the little plastic cover on the bottom screws and the screws--they did not come with the new handle. It took less than 5 minutes to do the whole job and while it was off I got to really clean my frig. Thanks for the quick delivery!!

simpley place the support into slot provided.

First, I shut off the water going to the refrigerator, then removed the ice bin. Then I loosened the two screws on the top of the ice maker (the one toward the front was a little tricky, since you can't see it at all), then removed the screw that fastens the lower bracket to the side of the frig. Then I lifted up on it slightly to remove it from the two upper screws, then unplugged the wiring harness from the side of the refrigerator and lifted the whole unit out of the frig.

I then removed the plastic cover on the front of the ice maker, pressed on the tab to remove the wiring harness from the old ice maker, and installed it on the new ice maker. I then removed the metal arm from the old ice maker and installed it on the new unit as well. The last part that I moved from the old ice maker to the new one was the lower bracket, as the bracket on the new ice maker was bent during shipping.

Once those parts were swapped, I put the plastic cover on the new ice maker, plugged the wiring harness back into the side of the frig, routed the fill tube into the back on the ice maker assembly, and set the unit back on the two upper screws. I then put the screw back in the lower bracket, tightened the two upper screws, and then put the ice bin back in and turned the water back on. After a couple of hours, I threw out the first couple of batches of ice and it is now working as it had in the past.

I also noticed, when looking at the old ice maker, that the black plastic coating was coming off the ice cube tray, so it was a good time to be replacing it anyway. Overall, a very easy job (I was prepared for swearing, parts being slightly off, etc.) and it would have been a shame to have paid someone to do it.

At first I went to a local part supplier and they didn't have it in stock but could order it for me for $55.00 plus $10.00 to ship it. I told them I would have to think about it. I went home and got on the computer and found your web site and was I shocked when I saw the same part listed for $6.98 and $7.00 to ship it. You guys saved me $50.00. The part arrived in two day and took 5 min. to install. I now have light in my refrigerator. Thank you.

Used socket set to remove screws. Removed the wire harness, then removed lift arm from old ice maker and then put lift arm on the new ice maker. Reinstall wire harness then installed back in freeze with the screws. Video was very helpful. I will do business with Partselect in the future. Shipping was very fast. Thanks Partselect

proped up frig, loosened screws, cut pin, installed rooler w/ new pin, rounded pin end, reistalled, lowered frig...everyone happy, thanks again partselect.

Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.

1. Removed the icemaker door
2. Removed the two screws from the underside of the icemaker unit
3. Removed the slide-on plastic cover that protects the power cable connector
4. Removed the icemaker unit
5. Removed the two screws from the control unit
6. Pulled the control unit from the icemaker unit
7. Installed the new control unit and reinstalled the icemaker assembly

A repairman wanted to charge me $250 to do what I did in about 20 minutes for about $120.

I removed all the screws except the top screws. These screws I loosed to make sure the door shelves remained in place. I did not want to remove the refrigerator door. I had read this method on PartSelect. It worked fine. I would recommend a power drill because of the number of screws supporting the door shelves; a power drill really help.

Please note there are only 3 sides of the "new" door gasket that are magnetized. It would have been nice to identify which are the magnetized sides before I did the installation; I guess I should have read the directions before hand.

It was an easy job.