Models > ART2107BC-PART2107BC0 > Instructions

ART2107BC-PART2107BC0 Amana Refrigerator - Instructions

Jump to:

All Instructions for the ART2107BC-PART2107BC0
76 - 90 of 135
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Judith from Phoenix, AZ
Parts Used:
8009
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Bulb Replacement
I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Joseph from Destin, FL
Parts Used:
W11384469
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
light switch would not work
Popped the old one out with a kitchen knife and popped the new one back in. It tool less than 15 seconds!!
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Janet from Flagstaff, AZ
Parts Used:
W11384469
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
The light went out
I pried the old one out with a screw driver and pushed the new one in. I expected instructions in the box it came in but there were none.
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ronald from Billings, MT
Parts Used:
W11384469
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Wrench set
non-functioning refrigerator lite switch
My owners manual said to unplug fridge from elec outlet, use a kitchen knife to gently pry off the switch plate
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!

Sincerely, Ron Marshall, Billings, MT
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Peter from Vista, CA
Parts Used:
W10833899
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
water inlet valve
real easy to install and it works fine. However, the problem was more complicated. The circuitry on the ice maker on the back side of where the gear that rotates the harvesting fingers had places that were not making contact. I took a dart, yes, a dart from my dartboard and pressed the copper contacts down so they made contact and all appears to be well. Well at least until tomorrow. yikes.
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Linda from GLEN CARBON, IL
Parts Used:
72032, 4392899
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
black scratchers from wheel chair
shook bottle and painted waited a day and repeated
3 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jackie from Nova, OH
Parts Used:
W11384469
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Switch was not working after a repairman had fixed something else
Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.
0 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Paula from Rush, NY
Parts Used:
W11384469
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
light switch sticking
I watched the video and thought "I can do this". Made some notes and then proceeded to remove the old switch and replace with the new one. Thank you.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Louis from Beloit, WI
Parts Used:
W11384469
Difficulty Level:
A Bit Difficult
Total Repair Time:
Less than 15 mins
Light did not come on (bad bulb!) on TC18KL
I have never before seen a bulb with the filament intact not light. If the bulb's filament seems intact, screw the bulb into a known working lamp and see if it lights. When screwing it back into the socket in the fridge, it takes a bit of extra effort to fully seat (until it does, it won't light!). For replacing the switch, I unplugged the unit, used a paint scraper and worked it under the switch bezel from the right side. A bit of moxie, and the switch came out. The replacement switch had a different spade contact spacing than the original. I used a pair of scissors to cut the rubber bridge between the two switch wire connectors so I could connect to the new switch. In the end, it turned out to be the bulb. NOTE: The Model TC18KL is _not_ listed! What I finally found that the number "P7803211WL" on the sticker is actually a manufacturing code. Found this out by searching, and Sears' part search came up with matches.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mark from Monterey Park, CA
Parts Used:
W10613606
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Overload/Relay burned up...
Removed and replaced part...
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from Grass Valley, CA
Parts Used:
W10613606
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers
R & R the overload/relay start capacitor in a Kenmore refrigerator.
After unplugging the refrigerator, I removed the lower rear access panel that exposed the condenser and the overload/relay start capacitor with 1/4" nut driver (6 total). Next, I unplugged the wire harness and spring loaded keeper with needle nose pliers. Then I pulled the overload/relay start capacitor out of the 3 pronged male receptor located on the side of the condenser and plugged in the new one. Replaced the keeper, plugged the harness back in, and replaced the panel. Very easy fix.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dora from Rock Island, IL
Parts Used:
W11384469
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
light would come on and off
Viewed the viedo - it showed what to do
Was this instruction helpful to you?
Thank you for voting!
Customer:
Alan from Trafalgar, IN
Parts Used:
W10613606
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Frig & freezer section would not cool/too warm
Easy to replace part - remove panel at the bottom rear of the appliance, unplug from the compressor and connect the new relay. Unfortunately, it was not the relay on my appliance -- looks like the compressor has gone out -- new fridge for me
Was this instruction helpful to you?
Thank you for voting!
Customer:
YSIDRO from SAN ANTONIO, TX
Parts Used:
W10613606
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers
Both sides of frig were warm- comp not kicking in
Logged in to internet, for whatever reason I selected your site. Good choice! Entered the model number and selected the symtems identical to my refrig. Ordered the recommended parts, (Relay and Start Capacitor), to solve the problem. Reviewed the remove and install video. Received parts as promised by del date. Installed parts under 15 minutes, Frig kicked in and frig has been working beautiful. Avoided all those added expenses of; home service check, amount of days in- shop repair, plus parts and overhead charges. Will recommend site to my friends.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Grant from Alexandria, VA
Parts Used:
8009
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Light bulb failure
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the ART2107BC-PART2107BC0
76 - 90 of 135