HMG521540 Admiral Refrigerator - Instructions

Removed old water valve on bottom right back side of fridge installed new one which actually took less work

Replaced the valve and cleaned all the coils at the same time. The ice maker is spewing out ice. Wife is happy again.

Used screwdriver & pliers to remove old brackets. Installed retainer on new brackets and snapped them into place in the refrigerator door.

Our refrigerator was no longer emitting cold air and clicking every 5 minutes in what sounded like a "starter" click and then a few minutes later an ending/"shutoff" click. Nothing else would happen between the clicks and we could still hear the freezer fan running in the freezer.

Frequent clicks meant that the starter relay was broken and that the condenser was not failing to start thus failing to cool.

I found very useful videos showing this process on Youtube but here are instructions:

Unplug the refrigerator and open up the back panel on the bottom. The condenser is a black round metal sphere in the center. To the right is the condenser coil which is a flat coil. Attached on the left side of the condenser is a plastic casing with wires coming out from the bottom, that is the relay housing.

Pull the plastic casing off, it is held by a metal clamp. Underneath the plastic casing is the relay. it is attached to the condenser with a straight long pin.

Pull the relay straight out, away from the condenser. You may use a flathead for leverage but I used some elbow grease and slowly wiggled it out.

Look at the relay. For my Admiral, the relay has a little headpiece that sits on the relay and connects to the pin. Otherwise you will have pulled out the relay piece and there will be wires connecting to terminals on the relay.

Remove the wires connecting to the terminals, noting which wires connect to which terminals. Take a picture on your phone if you need to. You may want to use pliers to maintain the terminal connectors on the wires and it may take some elbow grease.

Once all the wires are disconnected from the old relay, discard the old relay. You will know if it's faulty if you shake it and it sounds like it's full of broken glass. A new relay will not make that sound.

Connect the wire connectors to the new relay in the correct terminals.

Reconnect the new relay to the condenser by pushing it back onto the pin all the way.

Replace the plastic cover with the metal clamp.

Clean the dust off the condenser coils while you have the chance.

Replace the back panel and plug in the refrigerator. You should not hear any more clicking and you should feel the air from the freezer become cooler pretty quickly.

I tilted the unit back enough to scew the new legs into the threaded holes.

Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.

The firt hard thing was waiting for the part to arrive, but that went quick. The second hardest part was opening the box. Shucks I got a paper cut, should have used a razor but while wife wont let me have sharp objects. Oh, yeah I had to find the hachsaw. I fooled everyone I knew where that was too. Be sure to measure properly, because if you cut too short then you have to stretch the bar. I havn't found any type of bar stretcher that works. It's best if you clamp the metal bar to a 2 X 4 piece of wood in order to steady the metal bar while you cut. You can't cut to well trying to hold the metal bar in your hand. The best part was completeing the job by installing the bars. Finally I have more room in my freezer to store food in the doors. This is my story and I am sticking to it. Have fun.

It was easy after it was apparent that the run capacitor was plugged into the compressor. This was determined from a parts diagram of the actual model refrigerator. The part was the same but the location on the video was wrong. A large screwdriver was used to unplug the capacitor from the compressor. The temperature range of the refrigerator is still too wide but it's colder.

removed broken retainer with pliers and inserted new part. It was extremely easy---and I have ZERO mechanical skills.

Turn off water, removed two mounting screws, unplugged solenoid, removed incoming water connection and plastic pipe to ice maker. Installed new valve, connected water lines, reconnected plug, remounted with screws. Turned water back on, over rode power to ice maker and checked for leaks. Total time about 5 minutes. Very easy repair.

I had to cut the bar to the right length with a hacksaw. The most difficult part was getting on the plastic supports/pins on either end. I'm not sure a hacksaw is the best way to cut a retainer bar, but it worked.

bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what is inside the refer!

We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing

Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.

unplug the refrigator, remove everything from
frezer compartment. remove ice maker three screws and un plug. remove rear panel 4 screws
remove motor bracket from rear panel 4 screws
unplug motor . replace motor and reasemble in
reverse order. the new motor is very quiet.