GS24B7C3EV Admiral Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from BRISTOL, CT
- Parts Used:
- 70197-1
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Bottom shelf retainer, to keep products in, kept falling off causing bottles and other products to end up on the floor.
Tuned up the ends of the bracket with a needle-nosed pliers then installed new retainer clips into bracket. I then laid on floor and lined up two holes in door and bracket (one end at a time) and pushed retainer clips into door's existing holes. Door was open for less than 30 seconds. Bracket is now solid and holding. Note: Do not jam products in bottom or any shelf thus putting pressure on bracket. Find a new home for the product!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harvey from Alexandria, LA
- Parts Used:
- 69710-2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Original Ice Bin Rail Broken
Removed front screw and loosened rear screw. Old part came right out and installed new one replacing front screw and tightening both screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from METAIRIE, LA
- Parts Used:
- 70197-1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Brackets holding retainer bar on botton door shelf had broken.
Used screwdriver & pliers to remove old brackets. Installed retainer on new brackets and snapped them into place in the refrigerator door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gordon from Escondido, CA
- Parts Used:
- WP61003336
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken ice bin drive ring
Removed 6 screws to get at broken part. Had to remember the disassembly sequence to properly reassemble. The whole process was relatively simple. I saved about $125 which would have been the cost of a repairman coming to the house.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from GRANTSVILLE, MD
- Parts Used:
- WP61003336
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Drive ring disintegrated
Removed all screws on back and 4 on front. That part is easy IF you have a Torx of the right size. Slip out the ice bin a bit and replace the drive ring. Reassembly is a bit harder since some internal shift can occur -- rotate or tilt the whole assembly to get two -- I think -- screws started. No need to over tighten screws; snug is good enough.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Discovery Bay, CA
- Parts Used:
- WP2182124
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
The ice stripper cracked from freezing.
There was three screws to remove to unmout the ice maker, and unplug the wire harness,then two to remove to slip in new stripper. All took about 20 mins.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anna from Parrottsville, TN
- Parts Used:
- WP61003336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Metal Augar Damaged End On Plastic Ring I
Removed drive assembly end of ice bin using socket wrench to get to old ice bin drive ring. Pull drive sssembly back to get ice bin ring out of the other end of ice bin. Installed new ice bin ring and and reinstall drive assembly end.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathy from TEMECULA, CA
- Parts Used:
- W11384469
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Light switch broke off
We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jane from Albuquerque, NM
- Parts Used:
- 70197-1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Broken door shelf retainer
removed broken retainer with pliers and inserted new part. It was extremely easy---and I have ZERO mechanical skills.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David Barnes from ROSWELL, NM
- Parts Used:
- W11384469
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Rocker on switch broke off
Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randall from ponchatoula, LA
- Parts Used:
- WP61003336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
no ice in bucket
looked a website removed part found broken item order and installed in 15 minutes, easy simple fix very low cost change
rl
rl
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from GROVESPRING, MO
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
light did not work on the refrigerator side
bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what is inside the refer!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Neill from Albuquerque, NM
- Parts Used:
- WP70111-108
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Retainer bar was missing.
I had to cut the bar to the right length with a hacksaw. The most difficult part was getting on the plastic supports/pins on either end. I'm not sure a hacksaw is the best way to cut a retainer bar, but it worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- francis from longmont, CO
- Parts Used:
- 70197-1, WP70111-108
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
missing door shelf retainer
ordered new retained and fastners
cut to length per instructions
installed
repair completed
thanks for your service all parts were correct and deliver on time
wayne winkler
cut to length per instructions
installed
repair completed
thanks for your service all parts were correct and deliver on time
wayne winkler
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Saco, ME
- Parts Used:
- 70197-1, WP70111-108
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
cut to size and installed
I simply measured for the correcy length, cut with a hacksaw, inserted the ends that attach it to the door and installed it on the door ..... simple.
Was this instruction helpful to you?
Thank you for voting!