GS22X8DV (DR33B) Admiral Refrigerator - Instructions

Disconncted power, pulled plug on disconnect, loosened 3 ice maker attach screws, removed ice maker. carefully removed old broken part, to understand reasembly. Reinstalled new water fill & bearing part.. hung icemaker and tightened attach screws. Reattached electrical plug.. turned on power, it all worked. .took about 45 min to remove, 15 min to reinstall. Right tools needed re disassembly AND ASSEMBLY

Repair done according to video and instructions. What you need to know is myself and my husband are adverse to all kinds of "simple" repairs because they never go well and we are not handyman kind of persons. This, I must say, was a delightful change in our typical experience of attempting to make our own repairs.
Thanks
Sandy

Had to cut the old part off with dremel then just install new part and put back in refrigerator. It is a good thing to know that the Yoke is a left threaded. Thanks James from Pineville.

Removed top drawer from freezer. Unplugged the ice maker. Uncrewed the bottom screw. Loosened the two top screws. Removed old ice maker. Removed all the parts that didn't come with the new ice maker and installed on new ice maker. Reinstalled the new ice maker. Started making ice with no leaks in about 3 hours.

I switched the ring and still had the same problem. What caused the Drive ring to crack was the Ice maker drive was cracked also, when it filled with water it would tip. The ice was not freezing completely and would cause the ice to build up and the auger was froze with ice or a big piece of ice would jam it. So I replaced the Ice Tray, it is working like new. I have to buy another ice tray as inventory, although I know inventory is bad but I never agreed with that theory.

By replacing it with a new ine maker.

Very easy to install the new ice maker. Removed the bottom screw holding the ice maker to the side of the freezer. Loosened the top two screws. The old ice maker came off just like that. Unplugged the power supply from the freezer and removed the whole apparatus.

I saved the wiring harness, screws, cover, and metal arm from the old ice maker. Installed these on the new one and mounted the new ice maker in the freezer. Done.

The only issue I had was that the water supply hose got kinked when I pushed the fridge back into place. Once that was resolved, the new ice maker started happily making ice.

I tilted the unit back enough to scew the new legs into the threaded holes.

Removed old ejector arm and installed new part.

Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.

Remove bottom screw loosen 2 top screws unplug connector from back of icebox. Lift up and pull forward. Swap front cover full bucket stop bar and wire (plugs in) reinstall 10 minute job

Removed the screws that held the main ice bin and slid back the bin to leave space behind the auger to remove the broken ring. Replaced with new ring and replaced screws to hold ice bin back in place.

the diagnosis was the most difficult step.. and trusting that the one visible nut was the only thing holding it on.. (there are 2 other clips that you need to use a little force on to detach). remove the ice maker (one nut, 2 clips, detach plug).. then remove the 3 screws holding on the 'face' , pry face off, you will see where the 'contact' has burned/melted/worn away. replace unit. 80% of the time, this is the problem (according to my research)

Five minutes with a phillips screw driver and the cube maker was changed. . . In the process, I failed to unplug the unit, and shorted the fill valve in the back. Again, five minutes with a nut driver and it was changed. No need for a PHD or the cost of a service technician for either job.

Repair was as shown in the video except my refrigerator had screws instead of the plastic clips as shown in the video. Just had to loosen the two upper ones and remove the one lower one. All other steps were as shown in the video.