WFG515S0ES1 Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dennis from Dunnellon, FL
- Parts Used:
- WP8523178
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door bottom trim piece was rusty
Remove three screws, slid old trim piece off door. Slid new trim in place. Used ice pick to align screw holes and replaced screws. Total time about 15 minutes. Tip: used a bead of silicone sealer on the new trim strip to prevent moisture from causing new strip to rust.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Sinks Grove, WV
- Parts Used:
- WP3195097
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven bottom heavily corroded; difficult to clean.
Removed two screws holding the bottom in, pulled out old bottom, inserted new bottom, replaced screws and tightened them. Total time less than five minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from RIVERSIDE, CA
- Parts Used:
- 8009
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
light bulb in water ice freezer door went bad
I didn't. Don't know how to get to light bulb to change it for this specific model
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- karin from SURPRISE, AZ
- Parts Used:
- WP9758079
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Oven clicked, but would not ignite in gas range
Turned off power to range. Removed the lower panel that was secured by two screws, as well as the metal cover beneath it also secured by screws.. Removed the two screws securing the igniter, and pulled apart the black tubing that secured the igniter. (I had to pull hard to get it apart). Plug the new end into that same black tubing. screw in the two screws to secure the new igniter (this is tricky because one screw is hard to reach) I laid something in the base to cover the holes so I wouldn't lose a screw if it dropped. Screw metal panel back in, followed by the lower oven panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregg from SOUTH BEND, IN
- Parts Used:
- WP8523166
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
I broke a piece of the trim and had to replace it
took the handle off, replaces the side trim piece and replaced the handle. Very simple!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from HARRISBURG, PA
- Parts Used:
- WP9758079
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
When I put the Oven on Bake, it would not Ignite
Just took the bottom cover off the bottom of the stove, pulled the old igniter and put the new one on.
This did not solve my problem.
What do I need to do next?
This did not solve my problem.
What do I need to do next?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruno from LE ROY, NY
- Parts Used:
- WP8523175
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
bottom piece of range rusty
took old one off and installed new one used electrical tape to hold glass from sliding.Unscrewed moulding and installed new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from HADLEY, PA
- Parts Used:
- WPW10310922, W10761018, W10761014, W10491985
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broken Trim Pieces
Remove vent trim from oven and set oven glass to the side. Next remove handle from vent trim (two screws). Next place handle on new vent trim. Place glass in place, (it is held in place by bottom of oven door and vent trim). next place side trim in place and place that side of the vent trim and loosely tighten screw holding trim into place at top of the glass. Next place the other trim into place under the vent trim and tighten the screws on both sides.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dorothy from PORT ST LUCIE, FL
- Parts Used:
- WPW10299224
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
The door wouldn't close.
Watched a video on you tube!
When I ordered the hinge it was recomended to replace both hinges. so I ordered two hinges not knowing that one of the hinges didn't have a spring. I ended up with an extra hinge.
When I ordered the hinge it was recomended to replace both hinges. so I ordered two hinges not knowing that one of the hinges didn't have a spring. I ended up with an extra hinge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rob from GALENA, IL
- Parts Used:
- W11394363
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
One of the burner grates broke
Replaced the grate.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WILLIAM from SAINT JOSEPH, MI
- Parts Used:
- WP9758079
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
WOULD NOT HOLD DESIRED BAKE TEMP
REMOVE BOTTOM OVEN PAN. REMOVE GAS DEFLECTOR. REMOVE GAS TUBE. UNPLUG WIRE. REMOVE TOP AND BOTTOM SCREWS ON IGNITER. REPLACE IGNITER AND REATTACH IGNITER SCREWS. RE-INSERT IGNITER PLUG. REPLACE GAS TUBE AND DEFLECTOR. REPLACE OVEN BOTOOM PAN.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn from ROANOKE, TX
- Parts Used:
- WP9758079
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Gas oven would shut off mid cook
Removed grills. Removed bottom plate.
Removed flame shield.
Removed igniter, 2 hex head screws. Bottom one is a bit awkward. Disconnected wire. Installed new igniter. Careful not to drop stuff in the hole. Like a socket. I did
Removed flame shield.
Removed igniter, 2 hex head screws. Bottom one is a bit awkward. Disconnected wire. Installed new igniter. Careful not to drop stuff in the hole. Like a socket. I did
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from CROWNSVILLE, MD
- Parts Used:
- WPW10299224
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The hinge was mounted on the right . The screw to remove it got it's square head chewed up because of using the wrong ssize driver
I left the old broken hinge in place, & put the new hinge on the left side.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from BUFFALO, NY
- Parts Used:
- WP9758079
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven would lite once and after that it would just click 3 times and nothing, click 3 times and the same thing!
Removed the bottom pan and heat shield plate, removed the drawer to get to the igniter disconnect the one wire from it and removed it and just repeated the same process backwards to put the new one in. All under 15 mins
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from SAN ANSELMO, CA
- Parts Used:
- WP9758079
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
replace bake ignitor ; flame spreader removal difficulty
As the 2 screws in the front of the flame spreader didn't screw into anything , and made getting the flame spreader very difficult to remove, once I got the flame spreader out , I did cut off the screws so future install & removal would be easy. I had to hacksaw the screws off , as the screws are otherwise impossible to remove. The screws were damaging the oven metal sheet work during first removal ! Otherwise the new bake ignitor install would have been a very quick 20 minutes. Also I watched u-tube bake ignitor install & oven door remove videos, which were extremely helpful.
Was this instruction helpful to you?
Thank you for voting!