YWFE381LVS1 Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Doriss from Cartersville, VA
- Parts Used:
- 3149360
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Switch had burned out due to faulty wiring by electrician when appliance first installed
my son simply replaced the switch, so now I have a working oven light once again
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shirley from Las Vegas, NV
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light burned out in upper oven
Screwed in light bulb and glass protector
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- peggy ann from forest city, NC
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replaced oven lightbulb
very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from Phoenix, AZ
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bulb Replacement
I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joanne from Negaunee, MI
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven gets too hot,if set at 350 it heats to 550. Changed the sensor and was not the problem.
Took off the screws on the back of the stove and took out the sensor, and put in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bernice from Phoenix, AZ
- Parts Used:
- WPW10118455
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
I broke the glass by hitting it with the edge of a broom
Clean off all broken glass and wipe down the debree,figure what side the glass goes then unscewed the base then the sides then add gorrilla glue on the edges to help set the glass in place had some hold it the screw th center bottom in first then got the sides in place with the bottom rack then screw it all back in to place making sure the side and top were in place right that was it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Oceanside, CA
- Parts Used:
- W11594027
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Damaged Socket When Removing Bulb Base
This is a built-in oven, so the biggest problem was figuring out how to remove it from the cabinet. The solution turned out to be removing the cooktop above it and unscrewing two screws that connected the oven to the inside of the cabinet. The other problem was removing BOTH metal backs from the oven. The first one was easy. The second one wasn't. The old socket was recessed behind the second back, making it virtually impossible to access the metal "wings" that hold it in place, so I ended up pulling out the socket assembly from inside the oven with pliers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christina from West Des Moines, IA
- Parts Used:
- WP8203546
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
range installer broke a screw off & busted the plastic piece
Had to screw off old terminal block & screw on new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Elyria, OH
- Parts Used:
- WP8523175
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The original trim rusted
I did the repair by myself. I used masking tape to hold the side trim in place. It was pretty easy and it looks great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amadeusz from Simi Valley, CA
- Parts Used:
- W10856603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Broil heater exploded. The corner was burned/ corroded.
Unplug power. Remove panel on the back. Unplug heater.From front remove 3 screws and remove heater. Installed new heater. On the back restored connections - squized the lugs to have better connection. Put panel back. Plug the power and see if the coil get red. It looked good. Used oven few times it works fine. Difficoult part is to clean oven all around from accumulated grease. First repair for this stove, most of the time spend on figuring out what to open, no instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Veronica from Midlothian, TX
- Parts Used:
- W10823711
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Surface element was out
Disconnect the power.took the cooktop off the range. Turned it over. Removed the underside plate. Disconnected the bad element. Pluged inthe new element. Replaced the under plate. Reconnected the range to the stovetop .put cooktop in place. Reattached screws. Turned on power. Worked perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from Titusville, FL
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
E-2 F-3 codes..Oven inop w/trying to bake.Beeps @ start attempt.
Contrary to instructions(go thru front of oven) I had to pull out the range, remove two (2) screws from back chassis. At this point you pull out the connector, snap in new, reverse proceedure. Very simple. Hardest part is cleaning up debris generated by moving range.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Herriman, UT
- Parts Used:
- W10823711
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
burner not heating up
first I checked continuity through the surface element (burner) switch (rheostat) which was fine. then found the screws holding the burner top on and removed, this made it possible to lift up the burner top and remove the burnt out surface element.which was easy to see. take down the number, buy a new one and re hook up the four wires to the new element. (always mark down where the wires went)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ruben from Port St Lucie, FL
- Parts Used:
- W10823711
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Rear left burner,went out.
I did exactly what your instruction video showed. The most important thing to remember is to TURN THE POWER OFF FIRST.
Was this instruction helpful to you?
Thank you for voting!