GW395LEGT6 Whirlpool Range - Instructions

The repair was so easy. The part came in a box and as I expected it was an exact match. I closed my eyes...counted to three and behold the part was installed. I don't think that installation could have gone any better. I would buy again from this company if I needed parts for any appliance.

Open oven door. Remove covers from burner tube. Remove 2 screws holding igniter. Remove panel from back of range. Unplug 2 wires attached to igniter. Pull wires thru inside of oven. Reverse process to install new igniter.

Looked online and found it was probably the igniter which wasn't firing. An incredibly gratifying and easy experience with the self-fix. Worked on the first try just like new.

pulled door up and out. Disassembled door. removed old glass and rope gasket. installed new glass and gasket.

I was able to remove the door by opening it partially and lifting it up while jiggling it. Once off, I laid it with the inside up on a table and the screws along the bottom facing outward so I could access them easily. I removed the various screws and porcelain covers and sides feel of easily. The inside panel lifted off exposing the inner glass and frame. The screws and clips had to be sprayed with penetrating oil to remove them. The frame lifted off and the cracked glass was removed. I was careful to wipe away all the fluid used to loosen the frame clips. Assembly was the reverse of this being careful to let pieces fit nicely without force. It would have cost me $39 to have the repair performed assuming I could get the door off. A Phillip's head screwdriver was not adequate to remove the frame clips. You needed a correctly-fitting square drive.

Remove the bottom panel and confirmed that the igniter was not lighting. Unsrcrew the igniter from the housing in the oven, then removed the back of the range and unplugged two leads from their conections and ran the wires through the insulated back wall of the oven. To replace the part just did the opposite of above. Piece of Cake. Want to say also that I was astounded at the speed in which I received my part. Ordered it at 3:30 PM on Friday afternoon and received it by 10 AM Saturday. And with standard delivery! Thanks!

I went to the source of power on the stove and noticed one of the terminals had come loose from the terminal block and had shorted out against the cover of the terminal junction. After prying the loose terminal off cover I ordered new terminal block and received it the 2nd day. I removed the old terminal block and replaced the part in about 10 minutes..Thank you Parts Select for your easy to find diagrams and quick delivery.

No tools necessary. Shipment was extremely quick; I was very pleased.

Repair was super simple . Any one could have done it.

Removed the light cover - unscrew the bulb - place the gasket on the base of the light cover - replace the bulb - replace the light cover

Following the various instructions here made this replacement much easier! I was able to do this on my own with just a screwdriver. Pulling the hinges out was fiddly but after removing the screw and small hinge plate from each side a little wobbling and pulling with the door open an inch did the trick. After removing the door I started with the inside glass facing up on a table, and mid-replacement needed to flip the door over. So, recommend that you start with outside of door facing up. As you remove screws keep in mind where they came from so you can replace in reverse order properly. Other than that, everything went swimmingly! Thanks to everyone for their great advice.

Replacing an oven igniter is one of the easiest repairs you can make to your oven. There are two igniters - one for the broiler and one for the oven itself. Oven Igniter: Start by removing the rear panel of the oven which attaches with a couple screws. Inside the oven, remove the "butterfly" shaped heat deflector (over the flame tube) which attaches with four screws. You now have access to the igniter. Remove the two screws which attach it to the bracket. On the rear of the oven, unplug the two spade connectors. Pull the igniter out from the front of the oven. Fish the wires for the new igniter through the same hole. Plug the 2 new wires back in. You can't mess this up - the wires have matching connectors and you can't get them confused. The broiler igniter is a little more complicated. You will have to remove the side panel of the oven to reach one of the connectors. It's just a couple more screws. The procedure is the same, but the wires are much harder to "fish" through the hole though. Unscrew the broiler igniter from the bracket and unplug the wires. Before you pull them out, attach a length of clothes hanger so that you pull the hanger into the oven from the rear. This way you can attach the new wires to the hanger and then pull them through to the back of the oven. If you don't attach something when you pull the old wires out, it is very hard to fish the wires for the broiler igniter to the rear of the oven. Good Luck!

First of all I couldn't believe parts arrived next day. Parts solved the problem I was reluctant to believe new hinges would solve the problem. I installed the hinges in about 1 hour but I had door apart previously so I knew what I was doing. Now my wife is speaking to me again and she threw the wooden spoon away that she used to hold door closed. Just spent $100 dollars and saved $1600 thanks guys.

As a relatively handy person, I have built homes, and done every kind of repair you could imagine from plumbing to heavy construction. I never wanted to play with appliances, just couldn't read those diagrams well enough to feel comfortable. Parts select has changed my life and saved me so much money and I have repaired appliances in several of the homes with no issues using your videos and parts as my guide.

I did the repair myself while my husband was at work. I lacked the brute strength to remove the door, so I ended up taking in apart while it was in place. Unfortunately, I only now noticed that instructions for installation were provided on your website. I did it without instruction, just making sure to note where screws had been removed so I'd be able to reassemble the works when I was finished. The worst part was loosening a couple of the innermost screws--even after a long soak in wd40, they were really hard to crack loose. Once I managed that, though, it went smoothly. Don't be intimidated; you can do this stuff yourself without calling--and paying--a repairman.