CREW3874RW0 Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michael from Salem, OR
- Parts Used:
- WPW10434452
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The dual element control switches were no longer regulating the burners properly (either on or off, no in-between)
1. Pull the stove away from the wall and unplug the stove from the 240 volt receptacle.
2. Remove the knob from the switch (it just pulls off).
3. Unscrew the top half of the back plate of the stove and removed (about eight or so screws).
4. Unscrew the two screws attaching the control switch in the front of the control panel (these were hidden by the control knob just removed).
5. Pull out the control switch and detach one at a time the two sets of wire connectors attached to the switch. In order not to confuse which plug goes where, attach each connector to the new switch as you remove them. (Note: the connectors may be quite tight to the original switch; do not pull on the wires but simply work each connector gently until it slides off. They will reattach to the new control switch much easier.)
6. Reinstall the new switch to the stove in reverse order of removal. Make sure that the control knob, when the switch is reattached, is in the off position pointing straight up.
7. Reattach the upper back plate of the stove. For safety's sake, do this before reconnecting the stove to power.
8. Plug in the stove and test to ensure that the switch is working properly.
2. Remove the knob from the switch (it just pulls off).
3. Unscrew the top half of the back plate of the stove and removed (about eight or so screws).
4. Unscrew the two screws attaching the control switch in the front of the control panel (these were hidden by the control knob just removed).
5. Pull out the control switch and detach one at a time the two sets of wire connectors attached to the switch. In order not to confuse which plug goes where, attach each connector to the new switch as you remove them. (Note: the connectors may be quite tight to the original switch; do not pull on the wires but simply work each connector gently until it slides off. They will reattach to the new control switch much easier.)
6. Reinstall the new switch to the stove in reverse order of removal. Make sure that the control knob, when the switch is reattached, is in the off position pointing straight up.
7. Reattach the upper back plate of the stove. For safety's sake, do this before reconnecting the stove to power.
8. Plug in the stove and test to ensure that the switch is working properly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RAYMOND from JACKSONVILLE, FL
- Parts Used:
- 4396923
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broiler pan missing
ordered new broiler pan
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- patricia from chipely, FL
- Parts Used:
- WP355214
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
door of oven came apart when plastic screw holders broke
put back together with parts ordered. Parts arrived in 2 days!!!! and saved my large dinner party the following day from being ruined. Thank you so much for your parts inventory and for Jenn Air supplying only the part needed and not the entire door. It was a life saver!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gene from Turtle Lake, ND
- Parts Used:
- W11171119
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burned out stove top burner
Easy change! Two screws in front and grounding strap screw-lifted out and turned stove top upside down on table. three more screws for burner element and then reinstall with first two screws and grounding strap screw.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from kissimmee, FL
- Parts Used:
- W10856603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
top element was burnt out small burn hole in element
removed the screws that were on back side of oven securing panel that covered element terminals disconnected wiring to upper element then went in side oven area removing 4 upper mount screws that were holding upper element in place then removed old element and reinstalled new in same order was removed..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dennis from tonganoxie, KS
- Parts Used:
- WPW10107820
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven Self Clean Would Not Function
Take off the back panel of stove and unplugged timer motor and switch on door latch assembly,removed two screws that hold assembly and slide rod off. I put 110 volt plug to timer motor and it did not move, that is how I diagnosed problem. Ordered new assembly (cannot buy just timer motor)put new door latch assembly on and worked fine. Of course unplug stove before you start !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Fairfield Bay, AR
- Parts Used:
- WPW10107820
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Could not get self cleaning oven to engage
Removed back of stove, 8 screws, removed original latch assembly and installed new assembly. One thing that can cause you difficulty is that the rod that connects the assembly to the front latch on the door can disconnect and has to be reconnected.[Problem]
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PATRICIA from GEORGETOWN, MA
- Parts Used:
- W10763667
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Drawer Glide Snapped Off And Broke
Snapped in the new drawer glide. Took less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Land O' Lakes, FL
- Parts Used:
- W11171119
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
An Insect got in between the element coil & shorted it out
unplugged the range, removed the cooktop left & right front screws, unplugged left & right plug & unscrewed ground wire. Parts arrived fast & reassembled. . Happy, Happy, Happy! Happy Wife...Happy Life!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Lewisville, NC
- Parts Used:
- WP3149404
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Heating element would not get red hot
Replaced Infinite control switch in just a few minutes. Unfortunately the new switch had a lose terminal that was not supposed to be in the switch that came from the factory that way. I connected the switch, turned it on, and it instantly shorted the switch out. At that point the lose terminal was real easy to see.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rodney from Columbus, OH
- Parts Used:
- W10856603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
broiler didn't work
Removed original broiler element, and found it was open. Replaced with new element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alfred from Ann Arbor, MI
- Parts Used:
- WP3149404
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Left front 8 inch burner knob control stop regulating heat temprature.
I purchased a new infinite control switch 6". and replace the old one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Beth from Draper, UT
- Parts Used:
- W10856603
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broiler element EXPLODED!
Yes... it exploded. Ordered the part which was delivered promptly. Installed in about 30 minutes with a helper. Just unscrew the 4 interior screws and a bunch of the screws (10 maybe?) on the back panel. Drop the back panel, remove the electrical connections from the broiler element and have your helper pull it out. Shove the new one in carefully through the insulation, attach the two electrical connections and reattach all the screws. Worked fine but smelled a bit as it burned off the new coating. About a 30 minute project.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Adamsville, TN
- Parts Used:
- WP8523166
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Side trim broke
take the 2 screws that hold the handle on out...watch the glass front and the side trims because the handle holds them on. Take the glass out then remove the side trims. Replace the side trims holding the glass in place with 2 pieces of masking tape om each side then install the handle with the 2 screws and remove the masking tape.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from Saint James, NY
- Parts Used:
- WPW10107820
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Gas range would not go into self cleaning mode. When pushing the self clean button, would get three beeps!
The malfunction was narrowed down to the oven door motor lock, located at the upper left back of the unit. Removed two panels from the back of the unit, 8 screws. Then the motor, 2 screws, 4 wire connectors. Reversed the procedure for the installation, and solved the problem. About 30=35 minutes for the job. If your handy at all, it should not be a problem.
Was this instruction helpful to you?
Thank you for voting!