YWGE745C0FS5 Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Albert from Bryant, SD
- Parts Used:
- 242905
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
stove top got hot when using large pans
Removed the existing element and replaced it with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gene from Turtle Lake, ND
- Parts Used:
- W11171119
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burned out stove top burner
Easy change! Two screws in front and grounding strap screw-lifted out and turned stove top upside down on table. three more screws for burner element and then reinstall with first two screws and grounding strap screw.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from Saint Marys City, MD
- Parts Used:
- JEA7000ADSA
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old element cartridge no longer functions well, low heat
Lift large burner end of the element by the raised slot and pull old element out. Install the plug prongs of new element into cooktop plug and lower element in place. Done. My unit is 26 years old and I have replaced elements several times. I keep a spare on hand for replacement and the one I ordered is now my spare.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lance from Northfield, IL
- Parts Used:
- WP7430P044-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Erratic oven temperature, would not hold a setting or would get to that setting and then loose it shortly afterward.
Removed two screws on sensor in the oven. Pulled out stove and after unplugging same removed the back panel. Sensor has an electric connection on the rear of the oven with a connection that is easily separated. Threaded new sensor electrical connection through inside of oven and connected on the back of stove. Pushed insulation back around the wire were in goes through to the oven. Replaced back on stove and screwed in two screws which hold sensor inside the oven. Replaced back cover on stove, plugged it in and pushed it back in place. Did the trick for me..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Palm Coast, FL
- Parts Used:
- A341
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dirt on out-grille
Unpacked cover and placed it on Jenn-Aire grill.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PATRICIA from REEDSVILLE, WI
- Parts Used:
- JEA7000ADSA
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My burners were not working properly
It is just a matter of taking out the old cartridge and replacing it with the new on and it looks like a almost new stove. Works amazing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Land O' Lakes, FL
- Parts Used:
- W11171119
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
An Insect got in between the element coil & shorted it out
unplugged the range, removed the cooktop left & right front screws, unplugged left & right plug & unscrewed ground wire. Parts arrived fast & reassembled. . Happy, Happy, Happy! Happy Wife...Happy Life!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ERIC from SARASOTA, FL
- Parts Used:
- A341
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Jenn-Air grill burner covers (2)
No tools needed....just installed the accessory grill burner covers.
Was this instruction helpful to you?
Thank you for voting!