SF387LEGN4 Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from Maysville, GA
- Parts Used:
- WP8053334
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken rear stove drawer glide
Removed drawer, after removing the 50# of junk in the drawer, Used screw driver to remove screw that holds glide to drawer and then place new part into place put screw into hole and tightened screw. Replaced drawer and told wife not to put 50# of junk back into the drawer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from Maple Grove, MN
- Parts Used:
- WP8053334
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken Rear Drawer Glide
This was a very smooth repair. In total it took about 5 minutes. The pot drawer below the oven wasn't gliding like it once did. After I replaced the glides it works like new. Please note, if you are going to replace one side go the next step and replace both to provide balance to the drawer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rustin from LARAMIE, WY
- Parts Used:
- WP8053344
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
FAULT CODE F-3
REMOVE BACK COVER. UN PLUG, REMOVE TWO SCREWS IN SIDE OVEN, PULL OUT , REPLACE, REATTACH, FIXED CODE F-3
Was this instruction helpful to you?
Thank you for voting!
Broken drawer glides
Simply removed the bottom drawer, unscrew the old broken glide, and attach the new glide. Simple and no hassles.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Summerville, SC
- Parts Used:
- W10918546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
oven burner would not light
the research and diagnosis took much longer than the repair on this model. if i had the new igniter on hand, it would have been only about 15 mins.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from MORRISTOWN, IN
- Parts Used:
- W10918546
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
oven igniter quit working
pulled the stove out removed back cover, unplug then unscrew igniter. Mounted new igniter in place, plug it back in , put cover back on, put stove back in place. Took about 20 min. Very easy repair, thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from SAN FRANCISCO, CA
- Parts Used:
- WPW10118455
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Exterior glass of oven door broke spontaneously
We cheated; a local appliance repair company was called & the tech guy repaired it in 10 - 20 minutes. Couldn't be happier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael D from FULTON, NY
- Parts Used:
- W11032529
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The igniter for the front left burner was shorting out at the base of the ceramic preventing the burner from lighting.
Unplug the stove. Remove the burners. Release the top of the stove by using a screwdriver to push in the spring clips on each side of the stove top. Pull out stove to access the back of the stove. Remove the back plates. Identify the defective igniter wire and remove. Install the new igniter wire. Screw the back panels back on. Snap the stove top back in place. Reinstall the burners. Push the stove back into place and plug in the stove. Test the burners.
One precaution - make sure you do not move the gas tubing under the stove top out of position. If you do, make sure you put it back in line with the gas valves.
One precaution - make sure you do not move the gas tubing under the stove top out of position. If you do, make sure you put it back in line with the gas valves.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steven from LAKE WALES, FL
- Parts Used:
- W10918546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Too long to start.over 5 minutes when it did start.
Turn gas off at tank. Oven rack out. 2 screws out of flame spreader and remove. 2screws from ignitor. Pull oven out from location to access rear bottom cover. 2 screws out and unplug ignitor. Guess what ? Reverse order. Not worth paying gas company over 250 dollars.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- victor from alexandria, LA
- Parts Used:
- W10918546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
gas oven stopped working
I just removed the bottom panel in oven and the igniter was right where the flames should be and I removed the two screws and replaced with new part. I replaced bottom oven panel. You need to remove rear panel and plug wire and replace rear panel. My problem was solve. It took 20-30 minutes tops.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from CAMDENTON, MO
- Parts Used:
- WPW10202217
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
oven handle broke
new handle arrived black for white oven - screws did NOT fit new handle- glass came off the door when removing old handle
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gabriel from DENVER, CO
- Parts Used:
- W11032529
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
TOP RANGES WILL NOT LIGHT
I use the table knife to slide the side of the stove to open the top. then I traced one of the wire to where it was hooked up and remove it and replaced it. I did them one by one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lloyd from PRINEVILLE, OR
- Parts Used:
- W10918546
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Wrong part. The connection doesn't match.
Unscrewed the feet from the floor. Pried up the range top, removed burners. Unscrewed sides of the range from wooden cabinet it was recessed into. Unplugged range from outlet. Pulled range out into the open. Removed back cover. Discovered that I have the wrong replacement part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert Ruth from FERNDALE, WA
- Parts Used:
- WP3195097
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Corroded/greasy bottom oven tray
Loosened two screws and removed tray, very simple. Replaced new tray and adjusted screws to hold tray. Easiest part was finding new tray part number and ordering replacement using online parts diagram.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mace Matthew from Canaan, NY
- Parts Used:
- W10918546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The Igniter seized and the oven would not heat up..the gas would not light.
So....the oven stopped working.
I called a local appliance guy and set up an appointment to repair.
$90 to travel here.
$50 for the part
$ labor was about $75
..then tax.
BUT then....I had a moment of clarity.
A new Oven/Range/Stove top was about $400.
This guy was over $200 to repair a 4-7 yr old stove.
So I ordered the part.
A resus monkey could have fixed the stove...I really mean it...Easy is an under-statement.
I found a tutorial on you tube (how to change an Igniter.
Literally 6 screws and unplug the igniter and install the new igniter.
Replace the screws and replug in the unit.
and that's that.
I called a local appliance guy and set up an appointment to repair.
$90 to travel here.
$50 for the part
$ labor was about $75
..then tax.
BUT then....I had a moment of clarity.
A new Oven/Range/Stove top was about $400.
This guy was over $200 to repair a 4-7 yr old stove.
So I ordered the part.
A resus monkey could have fixed the stove...I really mean it...Easy is an under-statement.
I found a tutorial on you tube (how to change an Igniter.
Literally 6 screws and unplug the igniter and install the new igniter.
Replace the screws and replug in the unit.
and that's that.
Was this instruction helpful to you?
Thank you for voting!