WFE525S0JT0 Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michael from THE VILLAGES, FL
- Parts Used:
- WP3149400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burner wouldn't regulate temperature
Turned off power to range. Took back panel off to reveal all controls. Pulled off knob of bad control. Removed 2 screws from the front of the control. Pulled off wiring from back of old control. Took new control reversed procedure. Reinstalled back panel turned power on and tested new control. Total time about 20 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from TAYLORS, SC
- Parts Used:
- WP3149400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
surface element out
Unplug from outlet and top remove back section of range and unplug wiring from switch, remove knob and unscrew two screws and remove old switch. Install new switch reinstall screws and plug switch plugs into new switch (will only go on the correct way). reattach back and plug into outlet. All done and surface element works perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from YORK HAVEN, PA
- Parts Used:
- WP3149400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Right front burner would only stay on high
Turned off breaker, pulled stove from wall, took off knob, unscrewed and pull off backing from stove, unscrewed heat control part, unplugged wires, plugged into new part, installed part, replaced stove backing, replaced knob, pushed stove back in place and turned on breaker. It worked fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from ENID, OK
- Parts Used:
- W11594027
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
oven light kept burning out instantly
Replaced the oven light with a new one but it burnt out as soon as I turned it on. Therefore I decided a new socket may help.
My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.
The part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.
I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.
Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564
My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.
The part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.
I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.
Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from ONTARIO, NY
- Parts Used:
- WP8523178
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Rust on oven door lower trim.
Do not remove the oven door. (Not necessary.)
Remove the lower storage drawer.
While laying on the floor, remove 5 screws on bottom edge of door, two on each end, one in the middle. Middle screw is slightly different than other 4.
Caution: When removing the lower trim, the front glass may slip down. Be prepared to catch it. The side trim pieces may also slip out.
It helps to have a second pair of hands here. If needed: Slide the front glass back into place. Slide the side trim pieces back into place.
Position new lower trim piece, align holes. Start with the center screw, then the end screws. Leave all screws "loose" until all 5 are threaded, then tighten.
NOT recommended to caulk trim to prevent future rust. The caulk will act like glue on the front glass.
Remove the lower storage drawer.
While laying on the floor, remove 5 screws on bottom edge of door, two on each end, one in the middle. Middle screw is slightly different than other 4.
Caution: When removing the lower trim, the front glass may slip down. Be prepared to catch it. The side trim pieces may also slip out.
It helps to have a second pair of hands here. If needed: Slide the front glass back into place. Slide the side trim pieces back into place.
Position new lower trim piece, align holes. Start with the center screw, then the end screws. Leave all screws "loose" until all 5 are threaded, then tighten.
NOT recommended to caulk trim to prevent future rust. The caulk will act like glue on the front glass.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandeep from EDINA, MN
- Parts Used:
- W10777162
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
screw came off
very expensive to buy the part but just tighten the screw intot eh predefined place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from The Villages, FL
- Parts Used:
- W11171119
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Electric burner element not working
Video said to remove screws and lift stove top off, remove contacts and ground. My stove top was hinged and required me to lift and pivot stovetop up. The burners were anchored to the stove base not the top. I secured the topso that it would not drop down and proceeded with repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- bruce from PORTLAND, OR
- Parts Used:
- W11171119
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
surface element not working
Ordered new element from PartSelect. It arrived shortly. It did not match the original. Guy at appliance store explained how I could connect the wires on the new one. It still did not fix the problem. A repair man tried for 2.5 hours to fix it with no success. Now I will return the replacement element in the return envelope provided.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christy from OROFINO, ID
- Parts Used:
- WP3149400
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
I decided it was the switch that was bad as it would not turn on or anything.
After my husband replace it we noticed that our knob was worn to the point it would not turn on the new switch. I am sure the switch was o.k. so kept the old one and getting a knob to fix the issue.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from GROVE CITY, PA
- Parts Used:
- WP3149400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
bunner was not shuting off automaticly
I used the replacement video from the web site. The replacement went great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- bobby from HERSCHER, IL
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
range would not heat right
very easy watched the howto you gave
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- patricia from chipely, FL
- Parts Used:
- WP355214
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
door of oven came apart when plastic screw holders broke
put back together with parts ordered. Parts arrived in 2 days!!!! and saved my large dinner party the following day from being ruined. Thank you so much for your parts inventory and for Jenn Air supplying only the part needed and not the entire door. It was a life saver!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from LEBANON, VA
- Parts Used:
- W11594027
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Light would not light
Pop old one out and new one in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- pedro from HARLINGEN, TX
- Parts Used:
- W11047722
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
not instructions on how to install
the part conections were different from the original.so the first i did was to call parts direct to see if someone will help.NOBODY WAS ABLE TO HELP. so i had to use a lot of common sense to install this my self.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Scranton, KS
- Parts Used:
- WPW10245259
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Terminal block arc'ed because a wire had become loose.
Ordered and received the terminal block. Installed it along with a new 220V power cord and the appropriate insulator . Ensured the terminals were tight with a nut driver. Reinstalled cover. Then, using the control panel, I did a function check on all the heating elements, clock, oven light, to satisfy all operational requirements. All checked good! And, I was relieved that the control panel had not been shorted out as the terminal block was due to a loose connection. Easy fix.
Was this instruction helpful to you?
Thank you for voting!