WFE510S0HS1 Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- DAVID from SAN ANGELO, TX
- Parts Used:
- WPW10434452
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Front dual burner would stay on.
First I threw the breaker for the stove to off. I pulled the whole stove out, removed the back cover, removed the knob from the faulty control switch and then unscrewed the two screws holding in the switch. I then pulled the wires from the back of the faulty switch, inserted the wires into the new switch, reattached the two screws that hold the switch in. I threw the breaker back on and turned the burner on long enough to make sure that both dual elements came on and went off like they should. At that point I reattached the back cover and shoved the stove back onto its' slot. All is well and all went well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from SHELBYVILLE, TN
- Parts Used:
- WP3149400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
8” burner on low would run away. Burn solid red.
I installed the new switch. No difference. I switched elements with the other 8”. Same thing. I called Part Select and their rep said he doubted the new switch was defective but if it was they would replace it. But first how about trading the new switch with the other 8” switch that is working. I did that and the new switch worked fine on that burner but the old switch that worked before allowed the bad burner to go to red hot. Now I’m at a loss. All I see is a new stove. I don’t know what to do next and am open to any and all suggestions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- bobby from HERSCHER, IL
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
range would not heat right
very easy watched the howto you gave
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from The Villages, FL
- Parts Used:
- W11171119
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Electric burner element not working
Video said to remove screws and lift stove top off, remove contacts and ground. My stove top was hinged and required me to lift and pivot stovetop up. The burners were anchored to the stove base not the top. I secured the topso that it would not drop down and proceeded with repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from BRIDGEBORO, GA
- Parts Used:
- WPW10181986
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven temperature was 50 degrees off
Unplugged stove.
Pulled stove out.
Unscrewed screws and removed cover.
Removed & replaced sensor.
Reinstalled cover & screws.
Plugged in stove and pushed back in.
Only problem was when I pulled stove out, lid opened and disconnected the gas line to a burner.
Pulled stove out.
Unscrewed screws and removed cover.
Removed & replaced sensor.
Reinstalled cover & screws.
Plugged in stove and pushed back in.
Only problem was when I pulled stove out, lid opened and disconnected the gas line to a burner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from LEBANON, VA
- Parts Used:
- W11594027
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Light would not light
Pop old one out and new one in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- pedro from HARLINGEN, TX
- Parts Used:
- W11047722
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
not instructions on how to install
the part conections were different from the original.so the first i did was to call parts direct to see if someone will help.NOBODY WAS ABLE TO HELP. so i had to use a lot of common sense to install this my self.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- patricia from chipely, FL
- Parts Used:
- WP355214
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
door of oven came apart when plastic screw holders broke
put back together with parts ordered. Parts arrived in 2 days!!!! and saved my large dinner party the following day from being ruined. Thank you so much for your parts inventory and for Jenn Air supplying only the part needed and not the entire door. It was a life saver!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Scranton, KS
- Parts Used:
- WPW10245259
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Terminal block arc'ed because a wire had become loose.
Ordered and received the terminal block. Installed it along with a new 220V power cord and the appropriate insulator . Ensured the terminals were tight with a nut driver. Reinstalled cover. Then, using the control panel, I did a function check on all the heating elements, clock, oven light, to satisfy all operational requirements. All checked good! And, I was relieved that the control panel had not been shorted out as the terminal block was due to a loose connection. Easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RAYMOND from JACKSONVILLE, FL
- Parts Used:
- 4396923
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broiler pan missing
ordered new broiler pan
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from PLEASANT PR, WI
- Parts Used:
- W11178521
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Countertop Dishwasher - Non Whirlpool
Since I have All Whirlpool appliances in the home, the only one not a Whirlpool was a counter top dishwasher that looks exactly like it could be a Whirlpool and so not to be the odd unit out, I labeled it with with a Whirlpool logo nameplate on the face of the door. Now everything matches perfectly and all in the same exact color white too.
Just measured and marked where the plate was to be located, cleaned that part of the surface, peeled the backing and carefully placed the logo name plate in place and pressed it on. Voila. Done and looks original as well. Call me the big, deep fakearooski.
Just measured and marked where the plate was to be located, cleaned that part of the surface, peeled the backing and carefully placed the logo name plate in place and pressed it on. Voila. Done and looks original as well. Call me the big, deep fakearooski.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Gaylord, MI
- Parts Used:
- W11594027
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
oven light not working
replaced light socket but did not repair problem. must have burned the motherboard.
pleased with service from your company.
pleased with service from your company.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Caddo Mills, TX
- Parts Used:
- W11594027
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Inside Light would not work
Turned off CB for the oven,Remove the oven from the cabinet , remove the back of the oven, replaced the light Assembly. turned on CB for the oven, tested the light. and truned off the CB and replace the back and reinstalled the oven in the cabinet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joanne from Negaunee, MI
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven gets too hot,if set at 350 it heats to 550. Changed the sensor and was not the problem.
Took off the screws on the back of the stove and took out the sensor, and put in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!