CE301SP2W01 Uni Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Sheila from Monticello, IL
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Replaced heating element
I went to video and followed instructions. I removed the holding brace securing the element in and pulled out old heating wire and installed new one that came a day after I ordered it. It was so easy and saved me over $100
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Newburgh, NY
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
So easy!
First off the shipping was lightning speed and the repair was super easy anyone can do it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from Varna, IL
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Old element broke
All I did unscrew bolts pull out element wires detach them attach new element to the wires push them back inside the openings reattach bolts all done easypeasy and I am a 63 yr old woman
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Audrey from Miami, FL
- Parts Used:
- 3051163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
rear guide clips were broken
This was the easiest do it yourself repair job to be had so simple just push the new clip in the hole and you are done so easy. Audrey
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darlene from Allons, TN
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Bad element
Removed screws,pulled off clips,reinstalled new element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elsie from Commerce City, CO
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
heating element out
Took to screw out pull to wire's out push to wire's back on put the screw back on complete less than 5minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from Titusville, FL
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Bake Element in Oven
Quite easy and takes 5 minutes Remove racks from oven. Use a phillips screwdriver and remove 1 screw from each side of baking element. Gently pull baking element slowly or carefully so you do not damage wires, insulation around wires or so they don't come off element before you can reach them. With a pliers, hold the metal clip attached to wire and pull off of baking element. Make sure wire will not go back into back of stove. Pull off opposite side wire in same manner. Take new element, check the orientation of the element, make sure it it going in correct, and slide wire clip onto one end of element. Do the same thing with the other wire on opposite side. Carefully feed wire back into openings in oven while placing element back in oven.. Replace screws on each side of element to hold in place. Turn oven on so make sure it element is heating. I left my oven on 400 degrees to burn off anything that may have been on the new element during manufacturing so it would not leave or transfer an odor to food when using the next time.
Was this instruction helpful to you?
Thank you for voting!