Models > CE301SP2W01

CE301SP2W01 Uni Range

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for CE301SP2W01

Viewing 5 of 5
Keep searches simple, eg. "belt" or "pump".
This genuine OEM bake element is located on the bottom of the oven cavity to supply heat for baking. The approximate size is 19-1/2 inches wide by 18-1/2 inches long and has 3-1/2 inch inserts. The el...
In Stock
This OEM drip bowl fits under 8-inch burner elements and has a diameter of approximately 10-inches. Drip bowls catch any spills, and are a quick, easy, and cheap way to improve your cooktop aesthetic....
In Stock
This drip bowl is an OEM approved replacement part designed for use with various electric ranges and cooktops. This part is located underneath the burner to contain any spills while cooking. It fits ...
In Stock
If you are having difficulty opening or closing the drawer at the bottom of your range, the drawer glides may be damaged. These genuine OEM rear drawer glides help to support the side of the drawer an...
In Stock
If the storage drawer at the bottom of your range has become difficult to pull in or out, there may be an issue with one of your drawer glides. The drawer glides are used to help the drawer slide in a...
In Stock
This kit comes with the necessary components to replace your burner terminal block. It includes interchangeable mounting brackets, a terminal box, ceramic wire nuts, heat shrink protective tubing, and...
In Stock
If the burner element on your range is damaged or no longer heating up, the element should be replaced. When you remove the element, check the terminals for any signs of corrosion or arcing. If you fi...
In Stock
This is a genuine OEM 6-inch burner element for your electric range or cooktop. If the element is no longer heating up, it may be time for a replacement. When you remove the old element, inspect the t...
In Stock
Terminal blocks (also called terminal boards or strips) provide a convenient means of connecting individual electrical wires.
In Stock
$81.27
Sold individually.
In Stock
This switch controls the stove top surface burner.
In Stock
This broil element is found on the roof of the oven.
In Stock

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for CE301SP2W01

Viewing 8 of 8
Element will not heat
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Little to no heat when baking
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Door won’t close
Fixed by these parts
Fixing Fixing
How to fix it
Oven not heating evenly
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Will Not Start
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Little to no heat when broiling
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Oven is too hot
Fixed by these parts
Fixing
How to fix it
Touchpad does not respond
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
David from Shawnee, KS
Parts Used:
316075103
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Oven woudn't heat
1. Removed two screws, pulled out the element, voltage tested the element and determined it was an open circuit (bad element).
2. Ordered the part from partselect.com
3. Disconnected element, connected the new one, and screwed it back in.
1283 of 1361 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michael from Green Bay, WI
Parts Used:
316075103
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Element cracked in two pieces
Shut off circuit breaker to stove and collected the tool from the basement. Turned on flashlight. Unscrewed the two hex nuts from the old element/back of the oven. Slid the old element prongs out of the back, exposing the connecting wires. Pulled the connecting wires off of the old element, carefully, so that the connections wouldn 't come off of the wires. Threw the old element pieces in the garbage. Connected the new element to the connecting wires and re-fastened the hex nuts. My husband had wanted to call the repair man, but it didn't look too difficult, so I decided to try it on my own. Boy was he surprised when I fixed it, and for a fraction of the cost of hiring a repairman! Ladies, we can do this ourselves!!! :) Thank you for being there for us to order our part from, Parts Select, we had our new part in less than 24 hours, so the shipping was blazing fast!!! Keep up the good work!!! :)
813 of 918 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
bryan from sparta, WI
Parts Used:
3051163, 3051162
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
drawer glides were broke on front and back
used a screwdriver pushed the old ones out put the new in. the video instructions were great.
575 of 594 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!