CE301SP2W01 Uni Range - Instructions

It snapped right into the drawer, was very easy

Ordered new racks and replaced them.

Apparently, the original insulation had been removed due to a mouse infestation-the unit had been in storage for a while. After removing about 50 screws, I had all the body panels off and cleaned out the interior of the stove then installed the new insulation. I put it all back together and hooked it up- works just like new. I only paid 60 bucks for this oven, so all in all, not a bad deal.

Pulled out heating elements. Removed old drip bowls. Inserted new drip bowls and re-installed heating elements.

I was extremely pleased with the very quick delivery of needed parts.

pulled oven out, unplugged, unscrewed element attachment to the back of the oven (from the inside). element did not work. we tested the upper element and that did not work either. the burst of sparks, heat and flame from the shorting of the original element caused damage to the computer board. we called a local repair man to change the computer board, and then the unit worked, with our new element that we replaced!

I first unplugged the stove (which was the hardest part), I then set a bright light so I could see near the back of the oven. I then started the task of removing the old element by using a quarter inch nut driver, not to difficult at all. Once I removed the bracket I pulled it out far enough so I could disconnect the wires that were connected to the element. I had a bit of a hard time with one but after a little wiggling I got it loose. I was then able to remove the old element from the oven. I began the replacement of the new one, EASY ! I placed it in the oven, attached the electrical connection to the new element (made sure they snap in tight) and then replaced the bracket that held the element /coil to the back of the oven using the nut driver. All finished in about 15-20 minutes. I am not a strong woman , but a determined one. This fixed the problem and I am now baking like I have a new stove. The surface element is nothing to change , just unplug the old one and plug in the new one (simple). I use my front burner so much that it had began to smoke from so much food dropping and cleaning it over the years. MY main issue was the Bake Element and I really like my range and thought I would try this before buying a new range and I did it myself ! If I can do this anyone can believe me I am NO repair person, but this was very easy to do.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. The I reversed the process to install the new element which was exactly the same as the burned out one.
At first I was on the verge of replacing the whole stove before I decided to google " range heating elements". I ordered the part from your company and it arrived promptly.
Needless to say, I am thrilled that I don't have to buy a new stove. This one now works perfectly!

TURN OFF CIRCUIT BREAKER OR UNPLUG FROM SOCKET! Removed back of range panel: easy
Disconnected wires to elements: easy (one broken off)
Replaced connector: easy
Pulled both elements out and replaced: easy
Tested and replaced range back panel: easy

Be careful when handling steel panels...they can cut your hands! Use nutdrivers, they're better than screwdrivers. Use a good flashlight.

2 1/4 inch screws and 2 blade connectors fir the power. Took me longer to find my nutdriver than the repair.

The front glides easily snap into a hole on the sides of the range. The rear glides easily snap onto the sides of the lower rear of the drawer.

Took screws out back of oven to get to connectors . Pulled old conectors off Installed new element took about 5 min. Very easy job. Also good time to clean oven .

i at first had a hard time finding the model # on this older electric stove. i did a chat with a rep from partselect.com and they sent me a web site that showed me where to look for it. that helped a lot. found it and searched on partselect.com . they had just what was needed. the purchase was easy and shipping was fast. i was worried it was going to be time consuming finding what i needed, not true once i found their web site. also, installation was easy.

When I found the part I needed there was an instructional video on how to remove broken bake element and install new bake element. This was the best video short and sweet and anyone...I mean ANYONE could do it!

Step 1- cut off the power supply (I flipped by breaker, but you could just unplug the oven)
Step 2- remove baking racks
Step 3- unscrew the little metal plates inside the oven where the bake element meets the back of the oven (reserve screws for new element)
Step 4- carefully pull the bake element out until you have the wires through the holes
Step 5- carefully pull the bake element from the wire clips on both sides
Step 6- take broken element out of over and put new one in
Step 7- slide new bake element ends onto wire clips
Step 8- slide new bake element and connected wires back though back of oven
Step 9- used saved screws to screw metal plates on bake element to the back of the oven
Step 10- replace oven racks
Step 11- restore power to range
Step 12- enjoy a working oven and feel like an absolute PRO for fixing it yourself!!!!

purchased a square bit and removed screws easily and disconnected it from the wiring and pushed in the new element secured screw and it was back to baking.

Turned off power at the circuit box. After locating 1/4" nut driver (the hardest part of the repair)I removed the oven racks. Took the opportunity to wipe out oven. Removed the two screws holding the element in place.Pulled element out gently to expose the connections. Wiggled the terminal connector off the terminal on element. Gave the wire a little bend to keep it from pulling back into frame. Repeated process on other side. Removed new element from wrapper. Placed element on oven floor, reattached terminals--making sure they were on snuggly--carefully slid terminal ends back though slots in oven body. Lined up brackets, reinstalled screws, replaced racks and turned power back on. Turned oven on it worked. Made cookies! Very easy repair.