N9608*0 Roper Range - Instructions

Replace the connector and bracket, spliced the wires, put heat to the schrink wrap and I was done.

I raised the stove top, read the instructions to my son while he did the work, then I lowered the stove top, installed the burner, and it worked like magic.

I pulled the old filter out and replaced it with the new one.

After struggling with different methods for removal of the guide rail stop, I noticed a video on the screen with the part number PS2099534 shown. The video clearly described the process. Both guides were removed the dish rack was replaced, the old guides reinstalled in less than 5 minutes.
Many thanks for the helpful video.

I have to tell you the partselect.com video describing the replacement of a belt was the best I have ever seen. I chose to replace the idler pulley as well after receipt of the ordered belt and this was a good decision. The net of it was watching the video a couple times in advance of the effort was all the training required. I followed the video steps, found the old pulley, threw it away, ordered the new idler pulley, taped the new belt onto the drum, inserted the pulley, wrapped the belt past the pulley and onto the motor as instructed and applauded the ease of this effort.

One screw taken out, 2 wires switched, new part & screw put in. Burner like new!

Removed the original burner element sockets and replaced with parts provided in kit. Instructions were simple and easy to follow, problem completely solved in 20 mins!

The repair was simple. The filter arrived in just a few days after i ordered it. All I had to do was to remove the old lint filter and replace it with the new one. At the time i received the new lint filter I was a bit concerned because the lint filter was a bit bent being shipped in a box that was a git to small for the filter. That ended up not being an issue in the long run. I would recommend part select anyone needing parts.

gene mille

real simple,remove the two screws that holds the lent trap,then use a flat head screw driver to pop the front of the top up.then remove the two screws that holds the front to the sides,now lay the dryer on its back and remove the front and set it aside.now carefully pull the tub straight up and set aside.the idler pulley has probably fallen off its track,but know worries,it will go back once you have installed new belt.clean all of the lent that has been stuck around everything over the years.put the tub back in place,making sure that it ligns up correct.now put the new belt back making sure that it ligns up with the old marks.place the idler pulley back in place and turn the tub counter clocwwise to make sure it is aligned.put front back in place and snap the top on and reinstall the two screws in lent trap.

Cut power. Removed four attaching screws and raised stove top. Cut two wires of existing burner plug. Used existing plug to select correct plug configuration from parts in kit. Attached new plug and wires to wiring harness using connectors and heat-shrink tubing supplied with kit. Used hair dryer to shrink tubing on connectors. Closed up stove. Restored power. Burner now functional.

Cut the two wires approx 1 inch behind old connector and removed one screws to remove old connector, stripped approx 3/4 inch off the wires and connected them to the new wires on the new connector with wire caps and shrink wraps which came with the new connector. Replaced the old screw with the new screw and the job was completed. Be sure and disconnect power before starting!!

I looked at two or three repair stories on your site and followed the advice given there.

Three major things helped:

First, access to the innards by lifting the top AFTER RELEASING THE CLIPS AT THE FRONT USING A PUTTY KNIFE or similar - very helpful.

Second, instructions on removing the front panel and pulling out the drum were helpful

Third, a caution about checking and re-seating the rear drum seal using a putty knife or similar - I wouldn't have noticed that the seal was curled over in a couple of places without that warning - I'm sure it frequently gets bent over when replacing the drum.

PartSelect was very helpful and very quick in getting me the parts needed. I didn't realize I needed the idler pulley until after I received the belt I had ordered, but the pulley came so fast it really didn't matter - gave me time to clean out bags of lint - the worst part of the job.

Dryers are very simple, but hardy and enduring machines - enjoyed making a 30+(?) year old machine run like new.

Read instuctions first Turn breaker off to stove or unplug to be sure. Remove burner and drip pans. Remove scews holding socket in place if you are doing more than one make sure you keep in same location. Raise cook top untill supports latch in. Assemble plug it comes with two types holder compare to your plug. cut wire to old plug so you have enough wire to connect back with new. Strip wire back and place shrink tubeover wires wire nut together heat with a lighter or heat gun then do remaining plugges. place back in cover and replace scews. make sure wire are not to long to get under burner when cook top lowered. Lower cook top and clean burner plug ends with a little sandpaper to make sure they make good connection. replace pans and burner. turn on breaker or plug in stove making sure the burners come on when turned on good luck g.d.

It was a very easy fix. I followed the instructions that came with the kit and cut the original cable. Everything you need is in the kit; very few parts. Piece of cake and saved a lot of money an appliance repair person would have charged. This burner works better than the rest. I'm seriously considering replacing the other three blocks.

The four kits arrived, use of a pliers and shink wrap and side cutters...strip wires, twist wires connect wire ties, shrink wrap...little fire, plug the elements...done...four in about ten minutes...Instructions in each package...no problem...very easy...saved twice the money or more...Thanks for the parts...recommend this site purchase...parts arrived very timely...J. Iriwn