FGP337GQ1 Roper Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- michael from Reynoldsburg, OH
- Parts Used:
- 8184859
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
broken trim
remove the hinge stays they just clip in
remove the door. took out screw at bottom of door.
replaced trim.
replacing the door was a problem i didn't have pins to put in the spring loaded hinges so i used nails to hold hinge in position.
so make sure to open oven door first insert pins or nails in hinges then remove door. It would have took 10 min. to do.
remove the door. took out screw at bottom of door.
replaced trim.
replacing the door was a problem i didn't have pins to put in the spring loaded hinges so i used nails to hold hinge in position.
so make sure to open oven door first insert pins or nails in hinges then remove door. It would have took 10 min. to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James C. from Middletown, OH
- Parts Used:
- W10016380, WPW10202217
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken handel and trim
Un-screwed 4 screws. Got part numbers off of the pieces. Put numbers in blank on web site and ordered the pieces. Parts cam in 4 days later and installed the pieces with my trusty screwdriver.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from Litchfield, NH
- Parts Used:
- 4342528
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
The Oven igniter was burned out and needed to be replaced
First I Pulled the oven away from the wall and turned off the gas and unplugged the oven. I then removed the bottom drawer and the oven door to get easy access to the ignitor location. I then removed the oven racks and the 2 shields which cover the ignitor with a screw driver. I then removed & unplugged the ignitor and 2 screws holding the ignitor in place. This all took about 15 minutes. I then reversed the process and installed and assembled the oven. It only took about 25 min in total time and low and behold the oven worked again. Amazing the technology stuff. My wife things I am a genius...again. Not!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Galloway, NJ
- Parts Used:
- WP3195097
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
scratches and paint detoriation on bottom part of oven
Remove 2 screws holding oven bottom in place.Lift out the plate and replace with new plate. The hardest part of the replacement was lining up the screw holes. By the way i have never received such great service from any internet company as Part Select. I ordered the part on a Monday and the part was at my home the NEXT DAY and installed that evening.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- HERLIN from BOERNE, TX
- Parts Used:
- WPW10202217
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
dropped stove forward, handle broke and trim around it also broke.
Unsrewed what was left of the trim and oven handle. Just 4 screws total, then replaced the 2 screws of the trim and the 2 screws on handle.
Finished! Replacement parts fit perfect!!! Thanks a milliion!
Finished! Replacement parts fit perfect!!! Thanks a milliion!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Sinks Grove, WV
- Parts Used:
- WP3195097
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven bottom heavily corroded; difficult to clean.
Removed two screws holding the bottom in, pulled out old bottom, inserted new bottom, replaced screws and tightened them. Total time less than five minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mary lee from WEST DEPTFORD, NJ
- Parts Used:
- WPW10268483
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
change out burner grates
simple change out - remove old grates, install new ones - note that this site/store is excellent
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melissa from Mill City, OR
- Parts Used:
- 8184859
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Rusty bottom trim
Removed two screws and the front of the door popped off. Replaced the bottom metal piece that the glass front slides into. It was a piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles A from Clarksville, TN
- Parts Used:
- 3195610
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
broken glass
removed door handle screws then removed glass retaining tabs from sides put clips on sides of glass held insuation in place and replaced glass replaced door handle replaced two door screws trial opened and closed door successful done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from OWASSO, OK
- Parts Used:
- 8184859
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Trip to small for glass frame.
Replaced bottom trim included in kit.
Installed side door trim.
While trying to slide glass front in place both plastic side trims broke.
Had to use already broken door trim and glued in. Just hope when use oven glue doesn’t melt and will have to replace entire oven.
Installed side door trim.
While trying to slide glass front in place both plastic side trims broke.
Had to use already broken door trim and glued in. Just hope when use oven glue doesn’t melt and will have to replace entire oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leslie from Chesapeake, VA
- Parts Used:
- 4342528
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Gas oven bake cycle would not light; broil cycle worked ok.
Removed bottom pan from oven, removed gas flame deflector to expose ignitor and burner. Saw that ignitor was not working. Removed two mounting screws, pulled ignitor and wire until wire nuts were exposed and disconnected ignitor. Replaced with new ignitor, bracket and wire nuts. Remounted the new ignitor, and tested burner. Worked ok. Reinstalled deflector and pan, back in business.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from San Antonio, TX
- Parts Used:
- 4342528
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven wouldn't heat
I read some of question & answer to the problem I was having with the oven. When I saw do-it-yourself that all I need to know. Repair man quote me for 100.00 dollar he will do it plus part. So I save 100.00 dollar and done it myself. Thank to partselect for fast and quick delivery service. It was only 2 screws holding the element and the connector was a just plug it into the other plug very easy to do. I will always come back partselect for answer and help and buy the part from them. YOU ROCK PARTSELECT
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from CAMDENTON, MO
- Parts Used:
- WPW10202217
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
oven handle broke
new handle arrived black for white oven - screws did NOT fit new handle- glass came off the door when removing old handle
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bo from DENVER CITY, TX
- Parts Used:
- 4342528
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
oven would not light
took 2 screws out of bottom plate in the oven and lifted it out. removed 2 screw on the flame deflector and took it out. Took 2 screws out of old ignitor and unplugged it. Installed new ignitor tested oven put it back together. took about 30 min. screw driver only
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael D from FULTON, NY
- Parts Used:
- W11032529
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The igniter for the front left burner was shorting out at the base of the ceramic preventing the burner from lighting.
Unplug the stove. Remove the burners. Release the top of the stove by using a screwdriver to push in the spring clips on each side of the stove top. Pull out stove to access the back of the stove. Remove the back plates. Identify the defective igniter wire and remove. Install the new igniter wire. Screw the back panels back on. Snap the stove top back in place. Reinstall the burners. Push the stove back into place and plug in the stove. Test the burners.
One precaution - make sure you do not move the gas tubing under the stove top out of position. If you do, make sure you put it back in line with the gas valves.
One precaution - make sure you do not move the gas tubing under the stove top out of position. If you do, make sure you put it back in line with the gas valves.
Was this instruction helpful to you?
Thank you for voting!