BEP410WB1 Roper Range - Instructions

First removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...then replaced the old element with the new element..........(worked perfectly)

Unscrewed two small screws and took the old element out, and installed new element. It took less than ten minutes to repair. The new element works beautifully.

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

I first went to the breaker box and shut off the power to the oven.
Then I pulled the 2 screws from the back of the oven that held the element in and pulled off the clips and removed the old element.
My wife decided to give the old oven a good cleaning with a non-fuming cleanser while I went out to play golf.
When I came home she had applied the 2 clips to the new element and fastened it in with the 2 screws. (I love it when women use tools!)
The oven now looks and works like new!

Opened circuit breaker, unscrewed old element, disconnected old heating element wire, attached new element wire, screwed new element into place, closed circuit breaker. tested element for heat.

Removed two screws, removed two clips, removed the element and rehooked the two clips and screwed the two clips back in. Zip Zip.

My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

My daughter told me here oven had quit and ask my advice. I saw where the element was burnt. Took out 2 screws unkooked the wires. I was unable to get help at the local Appl repair store so I went to internet to parts select.com I put in model # and had the part within 3 days put it back in and worked fine.

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

Piece of cake. Removed door and racks, screwdriver to remove element. Reversed operation and back in service in no time. Good as new. Thanks.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Unscrewed 4 screws holding element. Disengaged one wire, but 2nd one was separated while pulling through rear wall. Could not grasp the wire from the front. Then unscrewed 4 screws along sides of oven to pull casing away from wall cavity. Sat oven on a box while unscrewing 12 rear panel screws. Pulled wire through from back into oven. (Didn't need to do this because new element extended through the rear wall to access from back. Could have reattached wires to new element from the rear, but didn't realize this soon enough.)....two days later reinstalled new broiler element reattaching wires inside the oven and replacing 4 screws holding element in the oven. To replace the back panel I had to lay oven on its face so the holes on back of would fit with the rear panel. Put 12 screws back on. Then pushed oven back into wall cavity and put 4 screws holding oven in place. It is now working!

Simple to unscrew the 2 screws holding the element to the back of the oven. Unclip the wires.

I observed that the lower heating element was attached to the lower rear of the oven by two stainless phillips screws. I removed the screws and gently pulled the element outward. The element came out easily with two large red wires attached (one on each side). I unplugged the wires and extracted the old element. I used this as an opportunity to clean the floor of the oven that was hard to get at with the element in place. I installed the new element by plugging in the two red wires and used the same two stainless screws to reattach.

Easy as 1, 2, 3