MGR6775BDS19 Maytag Range - Instructions

To replace the igniter, I removed the oven door, all racks, the cover for the burner element and the shield over the burner element. I also removed the back panel to access the wiring. Removal of these elements was easy and took only a couple of minutes. When I tried to remove the old igniter from the bracket supporting it, one of the screws was stripped. Unfortunately I had to drill this screw out and replace it. If I didn't have to do this, both jobs would have taken about 20 minutes combined. After removing the igniter from the bracket, I replaced it, ran the electrical to the back where the wiring harness was and reassembled the components.

As for the upper oven temperature sensor, it took 5 minutes. I removed the two screws holding the sensor in place and pulled it out which exposed the electrical connection. I simply unplugged it, and screwed the new one in its place. I then connected the wiring harness.

Watch the video. Spot on instructions. Easy peasy.

Remove the door.
Remove screws
Clear out broken glass. Vacuum out small glass shards.
Clean all glass.
Reattach all parts.
Replace the door.
Smile!

After reading from a Google search, why won't me maytag genius double oven light? I read that my oven will not open its gas valve until the igniter is hot, glowing red. Mine didn't glow red bad igniters. After ordering the new parts install was easy and under 15 mins. My advice is to be careful pulling the oven out to access the back panels, be careful not to scratch your flooring. 5 screws for the big panel, and 3 for the small panel. All Phillips head screws. 5 inside the oven to pull the old igniter. Easy job anyone can do it. I did both upper and lower ovens and the broiler igniters.

Bought new hinges as that was the obvious problem.
Below is the removal, installation process for new hinges. Turns out in my case there was nothing wrong with the hinges. Problem was still there after installing new ones. I found that the metal in the door that butted against the hinges was fatigued causing looseness. I ended up compressing the metal back into shape with a hammer. Problem solved but money wasted on hinges.
If you replace hinges. Here is what I did.
1. Open door slightly to where it stops in broiler position.
2. Remove the door by pulling up.
3. Remove two screws in front of hinges that hold them in.
4. Pull range out a few inches for access the remove the side fillers that trim out the stove.
5. Reach in from the side and work hinges out.
5. Pop in new hinges and reattach the 2 front holding screws and the side trim screws.
You are done.

Hired a pro. Parts are difficult to get on a timely basis today , if at all. Screw up this repair by damaging the outer " black glass " and you buy a new stove. It took three weeks to get my replacement glass even though PS said the part was being sent within a day of the order. Even so , I am am happy to have gotten it , and will continue to use the company.

Unplugged the old temp sensor at the back of the stove. From the inside I removed the 2 retaining screws. I taped a string to the old wire and pulled it through so I could pull the new harness through on the new sensor. When the new sensor arrived I installed it in reverse order. Easy peasy. Works great!!!!

The ignitor heated up and the broiler worked but not the bake mode. Repaired per instructions

Removed all the racks from inside the oven, unscrewed the 6 screws that held it into the cabinet, pulled it out and sat it on the floor in front of the cabinet. Removed the oven sensor from the inside of the oven after disconnecting the wire harness from the rear right exterior of the oven. Installed new sensor from inside (2screws), plugged it into the harness in the back and reinstalled oven in the cabinet.

Remove rear sheet metal cover. Disconnect the temp sensor wiring connector (on the left side as viewed from front).

Open oven, take out the 2 screws attaching sensor and remove. Reverse for installation.

Included wiring adapters are not needed for this model oven.

This is a double oven unit. Both the upper and lower igniters are easy to get to, with just a few screws to remove. However in order to reach the quick disconnects, the back of the oven needs to be removed. So there are a bunch of screws to take off and the oven needs to be moved away from the wall. Pulling out the igniter wires and putting the new ones back in, is easy. Then put all the screws back on and move the oven back to the wall. Don't forget to disconnect the power when you do all this.

I received my glass panel realy quick from Part Select. It was an eansy job to install the new pane.
It took less than an hour. Thanks for Your prompt service.

I had to wait week for parts that were supposedly in stock No notice about delay I had to call to find out you really dropped the ball on this one

Removed door, dissasembled door cleaned all broken glass, installed new glass, re-assembled door and put door back on oven.

Very simple project.

1. Slowly pull the stove from wall. 2. Unplug 120 volts plug from outlet. 3.Turned off the gas outlet. 4. Open the stove door, remove the racks, then unscrew (2) screws that hold the short oven sensor in place. 5. Slowly pull sensor out of it's housing. Remove the clip that holds the sensor. Install new sensor using the clip. Push sensor back through the hole opening. Screw the (2) screws into the mount to secure the sensor. 6. Plug the 120 volt plug into the wall outlet. Turn on the gas outlet. Test stove by turning on oven. It works like a new stove. Wife is happy, and Thanks Giving Dinner is on! Reverse your steps to secure your stove. A total of 25 minutes after cleaning the dust under stove. Thanks for everything. By the way, Thanks Giving Dinner was delicious.