MGR6775BDQ18 Maytag Range - Instructions

removed panel from back 4 screws. unplugged ignitor wire to lower level of upper oven, top wire is for broiler.Slid oven door off its hinges(very heavy)removed wire rack removed 2 screws from bottom pan lifted out,lifted off burner guard, looks like it may have had nuts to hold it down at one time , mine were missing. lifted out burner assembly. removed 2 screws holding down ignitor, they stripped out had to drill holes slightly larger and install new one with screws and nuts I had on hand. Used long screw driver pushed in from behind to guide ignitor wire back thru the insulation. reinstalled everything in reverse and it worked like a new. $50 part part saved us $2000, we were looking at replacing it with a new oven but we really liked what we had. Very satisfied, and wont hesitate to tackle next repair job with help from this web site.

Pulled the oven away from wall to access rear of oven. Disconnect electric plug from duplex outlet, turn off gas supply ball valve. Removed two screws that retain sensor on inside of oven. Disconnected two prong sensor connector at rear of oven. Tied a length of string to sensor connector wires. Pulled old sensor out through front of oven. Use the string to tie onto new sensor connector wires and pull new sensor into place from rear of oven. Retain sensor with two screws. At back of oven, used connector jumper supplied with part package to make connection to existing connector.

easy-peasy remove small panel on back
disconnect in the back of range-oven "orange wire"
unscrew igniter from burner inside oven
remove and replace with new one
slide wire thru hole in back of oven
reconnect---u r done
dave

Look in the oven. On the upper left corner is the sensor. Remove two screws. Gently pull the wire and connector through the hole and insulation. Disconnect old sensor, replace new. Gently push the connection through, then finish pulling through from behind the stove. Replace the screws inside the oven. Done.

I ordered the part one afternoon. It arrived before noon the next day. Then I simply removed the old seal (with about 2 dozen spring clips). Inserted the new part by carefully inserting the new seal into its corresponding hole at each end and then worked my way around the seal while inserting each attached spring clip into its corresponding hole.

Remove door, racks, unplug, remove lower burner cover two screws, the burner tube deflector pan two wingnuts, the burner tube. With igniter attached, remove back of range 4 screws to expose connector to igniter, unplug then remove burner tube, then igniter, replace igniter feed through back of oven wall and reconnect igniter reverse process and its done

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I then conected the new element and replaced te two screws. Turned on the oven & works fine.
Very Easy!

. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) pushed wires back in and secured sensor

Used cooktop creme, oven cleaner and Mr. Clean sponges. After many days of working on the surface, we were able to remove 99% of the sauce.

I removed the door from the oven and set it on towel on the table, and started the repair of the door. I removed the screws one at a time, and one layer at a time. Becareful you need to take the whole door apart, and remember how it goes bact together. In the end it was worth it. The hardest part was getting the right part. I thought I could order the whole door, and found out after several calls they don't sell the whole door. Part Select both times I put in my order had the parts at my door within 2 to 3 days. I also had to return one of the parts and within 2 to 3 days the part was credited to my account

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

I unplugged the power cord,removed the back panel and unplugged all the wiring harnesses.four screws hold the control in place. reverse to install. The instructions were very complete(I do this for a living so it was extra easy)Anyone following the directions could replace this in under 15 min.

I removed the two screws that attach the sensor to the oven wall. Then removed to more screws in the back of the oven and took off the rear cover, diconnected the sensor connector and installed the new sensor.

After reading some of the repair stories, I was hesitant about doing this task. It was really very simple, I just removed the screws from the back of the stove, and removed the old element. I then replaced it with the new one and replaced the back cover. This whole task from start to finish took 10 minutes. The oven heats perfectly now just like a new oven.

Had to unplug unit, remove back of unit (6 screws), then unscrew oven sensor (2 screws), then unplugged old sensor, replaced it and put back of oven on...Moving the oven out and working in the tight space avaialble was the most difficult. Other than that, super easy job that probably saved me a lot of $$$...