MER8880AW0 Maytag Range - Instructions

Slid oven out and took back shield off unplugged sensor took bracket screw out replaced sensor with new one.

I removed the bottom drawer,unplugged the Range and pulled it out to expose the rear cover panel. Using a nut driver (a screw driver can be used), I removed the rear panel to expose the Thermal fuse located almost dead center in the back of the Range. Unplug the two wires and loosen the screw holding it in position. Replace the thermal fuse, plug the two wires into the new part and replace the rear cover panel. Return the Range to its original position and plug it in. The job is done in less than 30 minutes.

Followed a video I found online showing how to replace the bottom bake element. It was very easy to do. I simply unplugged the over, removed the back wire cover and detached the damaged element connectors.

I then removed the bottom oven cover which conceals the element. Unscrewed and removed the damaged element and replaced it with the new one. Connected the wires to the new element and then Installed the bottom cover along with the back wire cover and plugged the oven back in. It was really this easy.

I've replaced oven heating elements before, but never in a 3 year old electric range oven. I watched the video again after the element arrived, and installation was easy with only 2 screw drivers. I was concerned about the repair when I saw the severity of damage to the old heating element and the underside of the bottom oven metal/ceramic plate, which was almost burned (a hole) through. After finishing the installation the oven showed it was preheating but no heat was being generated. A couple of phone calls later, a Whirlpool repair technician told me the main control panel needed replaced- $385 much higher cost due to chip shortage, inflation, and would take 2 months to arrive due to supply chain issues. So I don't know yet if the element is good or not. I am disappointed that the element blew in a relatively new appliance, but a total cost of $600 in a 3 year old oven is still probably better than $1200 for a new oven which is double the price I paid in 2018. Part failures never come at a good time but 2 months without an oven at Christmas & New Years is added frustration. When the heating element burned out there was a loud buzzing sound associated with the failure, which I've never experienced before and there were flames coming from underneath the bottom plate in the oven for an extended period of time. The repair for the heating element itself went smooth, but be advised you may get into more than just the element.

pulled stove away from wall. took back cover off by removing 10 screws. Identified switch number and ordered replacement switch. pulled knob off front and removed 2 screws from switch and pulled switch out. swapped switch wires and reinstalled switch, back cover and slid stove back into place. Very easy, the whole process took about 1/2 hour.

Simple-pulled range away from wall, unplug from socket. Removed back panel unscrewed thermoses and replace. Put back panel back on plug in, tested temperature setting before sliding range back on place

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Watch the video...

I first shut off the breaker, then, after pulling the stove away from the wall, I unplugged it. I removed the two screws in the back of the stove which came off easily. I removed the two screws inside the oven and removed the bottom plate. I noticed the heating element I was changing had braces along the bottom. I had to remove the two screws and removed the burnt out element. The new element did not have the braces the original element had, but it fit in perfectly. Then I replaced all the screws, plugged it in and turned on the breaker and it worked. The only thing that we noticed is there’s a clicking sound every time the temperature increases. Not sure what that is.

after watching the video, installed the temp sensor. Super easy

Removed back cover, replaced defective switch, had a little difficulty removing old switch harness. Othan than that a really easy fix.

very easy watched the howto you gave

very expensive to buy the part but just tighten the screw intot eh predefined place.

There is a good video on YouTube that shows exactly how to replace the bake element. Had mine fixed in 15 to 20 minutes. Saved me about $150 by not having to call repairman.

Replaced the oven light with a new one but it burnt out as soon as I turned it on. Therefore I decided a new socket may help.

My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.

The part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.

I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.

Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564