MER8880AW0 Maytag Range - Instructions

The You Tube video for replacing the Element was very useful. Let me know exactly how to proceed - it was easy.

The repair was successful. I know the dual element burner was good because it operated at full heat. After installing the dual element control switch, the burner was operating as expected with no further issues. After the back was removed, the dual element control switch was easy to access. After removal of the two Philips screws (and the knob), it's easy to pull out the switch to pry off the two cable harnesses (which are keyed). Removal of the cable harnesses was the hardest part because they come off very hard. I used a flat blade screwdriver to help pry off the harness. Installation of the new dual element control switch was very fast/easy, along with the back cover.

Following your installation, the old part came out easily, with new part installing easily., oven heat is being regulated properly..with range pulled out for part replacement, got that area cleaned too

the hardest part was moving stove to trplace part

Putting the drawer glides on was easy. My range drawer did not have any glides on so my drawer would fall out. The drawer glides popped right on the drawer. The glides for the track were easy to screw into the body of the range. I had to bend the tracks up a little on each side with a pair of pliers. One glide would go onto the track and the other one would go on top of the track. After bending them a little I was able to push them onto the track.at the same time.

Unplugged stove-Removed oven door two screws held the oven bottom pan removed same to observe the element removed thre fasteners removed inspection cover on back of the oven pulled off two electric wires replaced element reassembled easy job

Unplug range, remove cover from back of range disconnect red wires from element spade connectors. Remove oven racks, remove two screws from back of bottom tray, and remove tray. Remove screw from element bracket and remove element. Install new element and repeat steps in reverse order. Done.

Turn off the power to the stove, either by tripping the circuit breaker or unplugging the stove. Open the oven door. Unscrew 4 screws on the inside top of the oven releasing the cooktop.
Lift the front of the cooktop and release it from the retaining brackets on the back of the oven. The element will be exposed. Disconnect the wires remembering the locations. It is pretty simple because the wires are in a harness. There are three clips holding the element in place. With needle nose pliers, disconnect the clips from the surface. Remove the element. The retaining clips are in holes in the back of the element. The holes are numbered. Remember which number holes are being populated with a clip. Remove the clip from the old element and place it on the new element in the same hole #. Place the new element into the vacated space on the cooktop place the three clips in their respective places which will align the wires. Hook up the wires to the new element. Replace the cooktop (I cleaned it first) and screw it back into place. Turn the power back on and you should be good to go.

pulled the old gasket, the new one fitted perfectly. No effort at all.
An instruction sheet would be a bonus. I wish you put instruction sheet in all parts OR a web link for video instructions. a web link would be great

Took out 2 screws took old one out an put new one in it even came with a heating element to replace which was sooo very nice! I had very good service from ordering to receiving! Everyone was very nice I will deal with this company again!

I watched the repair video on this site and another on YouTube before I started. The rear panel has a different shape and two additional screws on the bottom edge. The power clip was easy to manipulate.
This was an easy fix for a seventy year-old like me!

Replaced the safety thermostat and disconnected the oven light.
Works great again...without the light

Very easy. Pulled the stove away from the wall. Used a screw driver to remove the two nuts to release the heat sensor, disconnected the wire, removed the sensor. Inserted the new sensor, plugged back into the circuit. put the two nuts back.
Beware, if the first time you put the oven on, if the error message comes back up (mine did) push the cancel/off button, wait a few minutes, put oven back on. System probably needed to reset. Mine worked perfectly after.

1993 model oven, built in wall model, so didn't to remove oven for the normal rear access to replace the lamp socket. As someone else posted, replacement can be done from inside the oven -- BUT the socket removal was more complex than just 'twisting it out.' But below worked! (1) Turned off oven power at circuit breaker panel. To facilitate working in the oven compartment, removed oven door (2 screws on back of door), raised the over door almost closed, put 2 large nails through the hinge holes when they lined up. Lifted the door out (heavy ~20-25 lbs) and put aside. (2) Put work light inside oven. (3) unscrew glass socket lens and the bulb). (3) Using inspection mirror, studied the inside of the socket to determine that its lock tab type and locations -> were on left and right sides of the socket. These tabs needed to be bent in, but they were each held out by a small circumferential length of think metal, a tab about 3/16" x 3/8". These small tabs could be moved/positioned by just finger friction, with a little start with a screwdriver tip on their edge! I got an end positioned to put sharp screwdriver under that end, then pried it (bent it) inward a short distance. Enough to use needle-nosed pliers to pull it completely out - came fairly easily. Repeated on other side of socket. (4) Then, with pliers, bent each of the 4 locking tabs inward a short distance, Used sharp tool to get one socket edge lifted a small amount; then use mini-pry bar and screwdriver to gently pry around the socket in steps, working evenly around its edge. At about 3/8", it was free. Lifted it inward gently so as not to damage the insulation of the 2 wires attached to its rear. Noted the direction of the wire tabs was straight up (keep same orientation on new socket). (5) Needle-nosed pliers on each connector to gently work the connectors off their socket tabs. Note one tab is larger than the other. Keep the wires inside the oven compartment. Don't damage the insulation. (6) Pushed the wire connectors onto their respective new socket tabs. Aligned socket with the tabs upward, and inserted it, careful to nurse the wires back into the oven wall hole; press socket into the hole, pushing it in evenly and firmly until flush. (7) Pushed in the new type bulb that came with new Socket. Turned on power, and light came on. (8) screwed on new glass cover. (9) Lifted oven back onto the hinge prongs. (easier with two people to get the prongs aligned and into their door slots.) Worked door left and right to get it to lower down fully. Removed nails, lowered door, and put its 2 screws back on. (10) Poured a glass of wine.

It was easy to remove the old oven door gasket. Just a little tug was all that was needed. Installing new gasket was just as simple as tucking in the gasket end into the hole at the bottom and pushing the clip in the corresponding hole.
TIP: roll the end of the gasket and feed into the hole then use a small tipped screw driver or the point of a needle nose plier to finish installing the ends into the hole at the bottom of the door opening.