MGR6751BDW17 Maytag Range - Instructions

Slide oven door off hinges. Remove old gasket. Instal new gasket. Used eraser end of pencil to help feed in ends of gasket into respective holes for excess. Note: job could have been accomplished without taking off door but I wanted to take door appart to clean inside and out of glass.

I removed the sensor from the oven using a philip screw driver. The sensor was removed by removing the two screws holding it in place in the upper left hand corner of the oven. I had to disconnect the sensor on the back of stove. Then I pulled the old sensor through the hole inside the oven. Then I installed the new sensor by putting the wire of the sensor through the hole where the old sensor was removed. Then I hooked up the wire in the back of the stove. Then took the screw driver and replaced the two screws holding the sensor in place. It was very easy to do and the oven is doing fine now.

My used stove had been dropped by the previous owner. While I could live with the minor scratches on one side the wooden shims holding up one corner were annoying. A new leveling leg was less than $2. I used a pair of needle nose pliers to straighten the mounting hole and screwed the new leg in. This used stove was originally $2000 but I bought it for $999. the new leg plus shipping was about $10. What a deal.

Followed instructions I found online at the Maytag site.

My first suggestion, after turning off the power to the unit, is to take the oven door off. Two simple screws and it's off! It makes getting to the temperature sensor much easier. I also moved the oven out so I could get access to the back to remove the rear panel. The ordered part came with two pigtails, neither of which fit my oven wiring harness. I cut one of them and the wiring from the faulty sensor, spliced them together with wire nuts and made my own connection harness. The new sensor went in with little effort. The wiring went together flawlessly with the spliced connection protected between the oven cavity and rear panel. Reattached the rear panel and the oven door, then slid the oven back into place. Turned on the electricity and back to normal! Problem resolved!!

Like other reviewers said it was pretty easy. Remember the order you take things off and keep the screws in groups so you remember which ones go back. I was a little surprised to see i had to take the bottom trim off door so that i could take out glass so i could reach brackets on top of door that hold on the handle, but this gave me a chance to do a good cleaning of the door. Not sure how grease gets inside the glass but there it was. Did this by myself but it would have been nice to have one more hand there to hold the glass as i put it all back together.

Undid screws on front and some on the back and replaced part and put screws back on and it fixed the proble

I had to pull the range out from the wall and loosen the rear cover to free the connector for the sensor as it got stuck on a corner guide. Put the new sensor in, rear cover back on, range back in place and tested the oven. Oven heats fast now and keeps a more even temp. Makes me wonder how long I was trying to cook with a bad sensor.

First, I called Sears who wanted $440.00 to send a tech out to repair the stove. Second, I visited various web sites to find out what the problem was. I watched a brief video on Part Select which showed the repair of the stove. I then checked other parts stores on the web and selected Part Select based on price and video. Installation was very easy just as the video showed. Stove was repaired in less than 30 minutes.

Ordered the oven sensor. Two screws to remove to replace old sensor. Since this was a slide in unit, you had direct access to the wiring harness. Used the adaptor. Total repair time about 20 minutes. A very easy do-it-yourself project.

Repair was super easy, Remove Screws. (the hardest part was trying to remove the edging of the door without cracking it, or breaking the tabs used to secure it) Once I got the edges off, I slid the front of the door off, removed the screws and braces holding the outer glass. Picked out the broken pieces, cleaned all the glass and inside the door and put it all back together. If I didn't clean everything, it would've taken half the time.

I have and in the wall Magic Chef oven CGW3330ADW seriel 10799876US that came the purchase of my home 10yrs. ago. After a black out and 2 brown outs my oven would not start and the F3 code is beeping and the "door lock" light was on but the door was unlocked. The clock was working fine, but could not use the timer or set the temperature. I googled "FLASHING F3 code" and one of the results was the comment thread on the Parts Select website. When I clicked the link I read several customers sharing their story that was very similar to mine. I was able to click on a video and see a short demonstration on "HOW EASY" it was to replace the "Short Oven Sensor Kit." I though, "Yea right!" I left a comment on that You Tube video with my make and model and a brief explanation of my problem. I received a reply to my comment with in 24 hours, confirming what other consumers had shared...The "Short Oven Sensor Kit" was needing to be replaced. I ordered the part for around $30 VERY late on Thursday evening and when I woke on Friday morning, I a shipping confirmation email. I received it VERY early on Saturday morning! I was able to replace the part very easily with in about 10 minutes. I was VERY LUCKY that I was able to to the repair WITHOUT having to remove the oven for the wall! I would have had to pay for help if I had to remove it from the wall. The Parts Select web site save me over $400 which was the estimate for the parts and labor from a local appliance repair business! I was told that it would probably be cheaper or about the same as buying a new over which was their recommendation. I am so glad that I decided to do the research and in less that 1 hour I had my order placed. Thank You Parts Select!

A fairly simple fix that this website did a nice job helping me diagnose and select the part. Only tricky part was the electrical connector on the range side had been cut so I had to splice the wires which wasn't a big problem. Just take your time to find the nuts and replace one part with another.

Removed top rail, removed front glass panel,Removed door handle brackets, removed door handle from bracket,attached new handle to brackets, attached brackets to door frame, slid front glass into place and reattached top rail. It was a great time to clean the glass.Good Luck

followed instructions and slid clips where instructed