MGR6751BDB19 Maytag Range - Instructions

the repair was not difficult ,take time cause back panel has to be removed to gain access to unplug the temp sensor ,it appear to work but the digital clock still flash not all the timebut it should not flash , not sure that i have fixed it

Remove the big back panel (5 phillips screws). Confirm voltage is present when attempting to start the oven by unplugging the PROPER ignitor. I say proper because initially I thought that the broil ignitor was the culprit. Very upper ignitor is the broiler ignitor and the next one down is the ignitor for the upper oven. You will notice that the ignitor plugs differ between broiler and oven. New ignitor should have a male end. Once I confirmed that voltage was present when attempting to turn on the upper oven and probing the ignitor terminal plug, I proceeded to remove the lower cover inside the oven (2 screws very front side) and remove the burner assembly. (First you'll need to remove the oven door, easy, just tilt out part way and slide it up and off of the rails). The ignitor is mounted to the burner assembly. It's inevitable, the 5/16 hex screws (x2) will absolutely strip out so make sure you have some extras on hand. Replace the ignitor, reinstall and you should be good to go! I've read that you shouldn't touch the element with your fingers as this will compromise the life of the ignitor. Good luck!

Removed stove from slot in wall. Bent rear left leg would not unscrew due to bent metal bracket. Used hacksaw to cut out leg, then straightened metal bracket with small hammer and was able to screw new leg in and adjust height by using level on stove before reinserting stove its slot. Recheck level after pushing back in place and adjust front legs if necessary. If not for bent metal receiving bracket, would have taken much less time. Still easy tho. R'cvd part in two days. Very quick.

This is a no brainer. I am only doing this because you asked. Pull out the stove, tilt it back, remove broken leg, install new leg.

My used stove had been dropped by the previous owner. While I could live with the minor scratches on one side the wooden shims holding up one corner were annoying. A new leveling leg was less than $2. I used a pair of needle nose pliers to straighten the mounting hole and screwed the new leg in. This used stove was originally $2000 but I bought it for $999. the new leg plus shipping was about $10. What a deal.

Like other reviewers said it was pretty easy. Remember the order you take things off and keep the screws in groups so you remember which ones go back. I was a little surprised to see i had to take the bottom trim off door so that i could take out glass so i could reach brackets on top of door that hold on the handle, but this gave me a chance to do a good cleaning of the door. Not sure how grease gets inside the glass but there it was. Did this by myself but it would have been nice to have one more hand there to hold the glass as i put it all back together.

Removed old gasket and replaced with new gasket'

very simple fix. I removed the bake burner cover (the blue cover on the bottom of the oven), under that is the oven baffle which is held on with one wing nut and removed that. Then remove the oven bake igniter screws(two on the side), remove the orifice cover scew and remove then remove the oven bake burner gently. once these parts are off you need to remove the screws on the back of the oven ( I believe theres about 4 or 5 along each side and there are 4 on the bottom of the large metal plate. you only need to remove the large metal cover every thing else stays put. Disconnect the lower back burner attatchment which just clips into the connecter. once thats removed the part should come out easlily from the inside of the oven. Now take the new bake ignitor and feed the wires through the opening on the inside of the oven that allows the wires to come through to the back of the oven(you may need to feel around for the wires and move some of the insulation aside to feel them) once the wires come through the back connect the new part by clipping it to the harness the old part was removed from. At this point you should be able to reassemble the back of the oven exactly the way it was removed.Now go back to the inside of the oven, replace the bake burner gently over the bake burner orifice and put the orifice cover back on and reattach with it's screw. Position the bake igniter back into place on the side of the bake burner and replace the two screws previously removed. Once thats in place its time to put the oven baffle back on and secure with the wing nut and the last step is to place the bake burner cover. Just set the oven to bake and it should be working if thats in fact the problem..Good luck. Took me less than 15 minutes to fix.Some find it easier to remove the oven door but I didn't need to do this since I had enough room to access the front and the back of the oven without any trouble.

Followed instructions I found online at the Maytag site.

removed the door, removed the bottom, removed the glass. The handle bracket it attached to the door but though the vented part. After removing the old handle just had to put it all together again, Not hare just a lot to take a apart.

I unscrewed the door's top edge, removed the bottom drawer to loosen the oven door's bottom edge to where its screws were hanging in by a thread. The outside glass was then removable and exposed the screws holding the door handle mounting pieces. I unscrewed the four screws that held the mounts to the door, then the two that held the handle to the mounts, replaced the broken handle with my promptly delivered new one and reassembled the door in reverse order of above. Oh yeah, reading the other accounts of how to do this was the most important step in all this.

Slide oven door off hinges. Remove old gasket. Instal new gasket. Used eraser end of pencil to help feed in ends of gasket into respective holes for excess. Note: job could have been accomplished without taking off door but I wanted to take door appart to clean inside and out of glass.

removed oven door, unscrewed 2 screws on front of plate covering burner at bottom of oven. Undid wing nuts on tent-like cover, unscrewed 2 screws at back of burner (igniter "hiding" under left back side). Pulled oven away from wall (yuch, where did that stuff come from?), unscrewed 2 screws of bottom plate, undid connector to old igniter, fished wires with connector from new igniter, plugged them in. Attached new igniter to bottom of burner, rescrewed. Put all screws and parts back in correct places. Cleaned oven door before putting it back on. Turned oven on........baked bread!! Hooray! Repair was easy-peasy!

1. Opened oven door and removed bottom covers plates to expose igniter and removed it. 2. Located hole in oven rear where the igniter connector and leads went through. 3. Pulled oven forward to allow access to rear bottom left cover plate where leads came through and removed plate to obtain access. 4. Installed replacement igniter in place of old iginter and ran its leads and connector through the oven hole. 5. Since the new igniter connector was unlike the old one, I had to replace the new igniter connector with the old one. Allowing sufficient lengths to properly make splices, I cut the igniter connectors off so that I could eventually match the mating connecter to the oven control circuit. I used a wire striper and pliers to make good splices. I covered the splices with plastic wire nuts normally used for insulating splices. I left the splices and the igniter connector outside the oven back for protection from the heat inside the oven. 6. After ensuring that oven insulation material was positioned to essentially cover the hole where the connector wires go through, I replaced the cover plate at rear of the oven and the cover plates inside the oven. 7. I checked oven for proper operation and found it now to be OK. Range was returned to normal position..problem corrected.

The range in my classroom had the leveling legs broke off by the summer staff. I ordered two new leveling legs and the night custodian replaced them in about 45 minutes and them leveled the stove. Parts were just as stated and easy to order.