MGR6751BDW Maytag Range - Instructions

I followed the instructions on this website. Luckily a friend showed me where the sensor was located and from there, it was a breeze. Removed six screws on the back oven panel, removed two screws inside of the oven, took the old sensor out and put the new sensor in. Voila - works great. I can't tell you how much I appreciate Parts Select and the feedback and help from the customers. I've been out of work for almost two years and when I called my repair guy, he said it could be the computer and that would be expensive. That's when I searched on line and found Parts Select. I would have never even attempted this on my own if it weren't for you and it was so simple. Next time anything goes wrong with an appliance, I'll be contacting you first! Thank you.

I think the installation instructions are fairly self explanatory. This is the second item I've ordered from Parts Select and I'm thrilled with their service. The items are always less expensive than other sites and they deliver what they promise. I would highly recommend them.

A fairly simple fix that this website did a nice job helping me diagnose and select the part. Only tricky part was the electrical connector on the range side had been cut so I had to splice the wires which wasn't a big problem. Just take your time to find the nuts and replace one part with another.

Removed top rail, removed front glass panel,Removed door handle brackets, removed door handle from bracket,attached new handle to brackets, attached brackets to door frame, slid front glass into place and reattached top rail. It was a great time to clean the glass.Good Luck

very simple fix. I removed the bake burner cover (the blue cover on the bottom of the oven), under that is the oven baffle which is held on with one wing nut and removed that. Then remove the oven bake igniter screws(two on the side), remove the orifice cover scew and remove then remove the oven bake burner gently. once these parts are off you need to remove the screws on the back of the oven ( I believe theres about 4 or 5 along each side and there are 4 on the bottom of the large metal plate. you only need to remove the large metal cover every thing else stays put. Disconnect the lower back burner attatchment which just clips into the connecter. once thats removed the part should come out easlily from the inside of the oven. Now take the new bake ignitor and feed the wires through the opening on the inside of the oven that allows the wires to come through to the back of the oven(you may need to feel around for the wires and move some of the insulation aside to feel them) once the wires come through the back connect the new part by clipping it to the harness the old part was removed from. At this point you should be able to reassemble the back of the oven exactly the way it was removed.Now go back to the inside of the oven, replace the bake burner gently over the bake burner orifice and put the orifice cover back on and reattach with it's screw. Position the bake igniter back into place on the side of the bake burner and replace the two screws previously removed. Once thats in place its time to put the oven baffle back on and secure with the wing nut and the last step is to place the bake burner cover. Just set the oven to bake and it should be working if thats in fact the problem..Good luck. Took me less than 15 minutes to fix.Some find it easier to remove the oven door but I didn't need to do this since I had enough room to access the front and the back of the oven without any trouble.

unscrew side and bottom panel, fix the inlets that hold the glass, slide the new one and put the screws back in. Tip: It's better to remove the whole gate before start.

My used stove had been dropped by the previous owner. While I could live with the minor scratches on one side the wooden shims holding up one corner were annoying. A new leveling leg was less than $2. I used a pair of needle nose pliers to straighten the mounting hole and screwed the new leg in. This used stove was originally $2000 but I bought it for $999. the new leg plus shipping was about $10. What a deal.

shut off gas and unpluged stove pulled it away from wall removed(2)screws from (top left inside oven)unpluged old sensor in back(left side)and pull old wire thru feed wire from new sensor thru hold pluged in put(2)screws back in done(***used drinking straw and tape to feed new wire thru hole***)

This is a no brainer. I am only doing this because you asked. Pull out the stove, tilt it back, remove broken leg, install new leg.

It was easy because the clips were already on the new door gasket. Just had to remove old door gasket and replace it with the new one. Very simple job.

Removed old gasket and replaced with new gasket'

followed instructions and slid clips where instructed

Cut off the electricity at the junction box. Removed two screws from the sensor at the back of the oven. Then pulled the sensor with the wire out of the installation hole in the back of the oven. Disconnected the quick connect plug from the sensor and reconnected the new part. Reversed the process and screwed the two screens back into the oven wall. Turned the electricity back on and started up the oven. (Everything ran well for about three days when the oven again signaled "F-5" indicating the oven was again not functioning properly. Restarted the oven and is currently running properly. My spouse does a lot of baking with this oven for cookies, roasts, etc. Next time it fails I will be forced to call a repairman as I believe there is something wrong other then the heat sensor.

First I took the door off and outside to dump the glass in the trash which I had some Kevlar gloves so not to get cut. Removed the three screws on the bottom trim piece and the two on the sides remove the outside face glass next remove the four screws that hold the next glass. This glass is in a frame there is bent tab on one corner unbend open frame and install inner glass close frame rebend tab and reinstall all the parts.

I disconnected the electrical power, but not the gas line, and pulled the oven unit away from the wall. I unscrewed the old temperature sensor mount and only realized then the simple configuration: A wire from the sensor runs through the back of the internal oven space to the back of the oven unit through a thin space filled with insulation. The old sensor was easy to disconnect behind the oven unit and pull the old sensor and wire forward through the opening in the oven. The most challenging part was threading the new sensor wire from the oven interior through the back of the oven unit. The instructions and comments provided on-line by previous customers was EXTREMELY helpful. I wish I could do many more household repairs like this!