MGR6775BDW Maytag Range - Instructions

You had the part at a good price and super quick delivery.

Ordered and received the terminal block. Installed it along with a new 220V power cord and the appropriate insulator . Ensured the terminals were tight with a nut driver. Reinstalled cover. Then, using the control panel, I did a function check on all the heating elements, clock, oven light, to satisfy all operational requirements. All checked good! And, I was relieved that the control panel had not been shorted out as the terminal block was due to a loose connection. Easy fix.

ordered new broiler pan

I determined the bake igniter was not working. If the bake ignitor does not work, the sensing unit to turn on the gas does not activate. I examined the bake igniter it was blacked significantly in one spot. There were no apperant cracks in it. I did a web search for the part and ordered it. Three days later it was delivered. Take pictures of each step if you fell the need. Pull stove away from wall turn off the gas, unplug power cord, remove panel in back of stove that covers the electrical, unplug the ignitor/element. Move to the front of the range and remove the oven rack. Remove the cover over burner tubes, it secured with several screws. Remove wing nuts for heat shield. Carefully remove burner tubes along with the attached ignitor/element. You will have to carefully guide the ignitor wires out with the burner tubes. Unscrew ignitor from the burner tube, attach new ignitor/element. Reverse the steps.

I pulled the oven door off and set it on the counter. I unscrewed all the visible screws and carefully removed the glass. Found some more screws that needed removal. Removed the old handle, attached the new. Then re-assembled everything. I kept parts aside in the order I took them off, so I knew what order to re-assemble. My only problem was the weight of the door as I am a 74 year old female and, to me, the door was very heavy. Otherwise it was not a difficult task.

Remove two screws back panel and remove sensor two screws inside top oven.

Once I saw the spring clips on the new door seal, it was easy to understadn how to remove the old seal and install the new one. Looks nice !

Removed the two screws pulled the element out and unhooked the wires then used one of the included adapters to reinstall the new sensor then screwed the two screws back in to secure the sensor. Everything works fine now.

I took out the old and replaced with the new. The hardest part was getting that tiny halogen bulb in that tiny little hole. It took longer to take the oven racks out and put them back in than to make the repairs.

unscrewed screws in the back of the stove. inside the stove, replaced the old bake igniter with the new one and connected the electrical wire in the back of the stove.

Just remove the old for new

After we got the part in the mail my husband put it on and shortened the wires and put new plugs on the ends of the wires and we had to get a new plug put it on and it was fixed.

I removed the sensor from the oven using a philip screw driver. The sensor was removed by removing the two screws holding it in place in the upper left hand corner of the oven. I had to disconnect the sensor on the back of stove. Then I pulled the old sensor through the hole inside the oven. Then I installed the new sensor by putting the wire of the sensor through the hole where the old sensor was removed. Then I hooked up the wire in the back of the stove. Then took the screw driver and replaced the two screws holding the sensor in place. It was very easy to do and the oven is doing fine now.

First, I called Sears who wanted $440.00 to send a tech out to repair the stove. Second, I visited various web sites to find out what the problem was. I watched a brief video on Part Select which showed the repair of the stove. I then checked other parts stores on the web and selected Part Select based on price and video. Installation was very easy just as the video showed. Stove was repaired in less than 30 minutes.

very simple fix. I removed the bake burner cover (the blue cover on the bottom of the oven), under that is the oven baffle which is held on with one wing nut and removed that. Then remove the oven bake igniter screws(two on the side), remove the orifice cover scew and remove then remove the oven bake burner gently. once these parts are off you need to remove the screws on the back of the oven ( I believe theres about 4 or 5 along each side and there are 4 on the bottom of the large metal plate. you only need to remove the large metal cover every thing else stays put. Disconnect the lower back burner attatchment which just clips into the connecter. once thats removed the part should come out easlily from the inside of the oven. Now take the new bake ignitor and feed the wires through the opening on the inside of the oven that allows the wires to come through to the back of the oven(you may need to feel around for the wires and move some of the insulation aside to feel them) once the wires come through the back connect the new part by clipping it to the harness the old part was removed from. At this point you should be able to reassemble the back of the oven exactly the way it was removed.Now go back to the inside of the oven, replace the bake burner gently over the bake burner orifice and put the orifice cover back on and reattach with it's screw. Position the bake igniter back into place on the side of the bake burner and replace the two screws previously removed. Once thats in place its time to put the oven baffle back on and secure with the wing nut and the last step is to place the bake burner cover. Just set the oven to bake and it should be working if thats in fact the problem..Good luck. Took me less than 15 minutes to fix.Some find it easier to remove the oven door but I didn't need to do this since I had enough room to access the front and the back of the oven without any trouble.