MGR6875ADS Maytag Range - Instructions

oven had to completely come out cause two sheet metal side panels had to be removed to get to hinge.

Simply remove two screws take old one off and line up and put new one on and replace the two screws. Couldn't have been easier.

Hired a pro. Parts are difficult to get on a timely basis today , if at all. Screw up this repair by damaging the outer " black glass " and you buy a new stove. It took three weeks to get my replacement glass even though PS said the part was being sent within a day of the order. Even so , I am am happy to have gotten it , and will continue to use the company.

After reading from a Google search, why won't me maytag genius double oven light? I read that my oven will not open its gas valve until the igniter is hot, glowing red. Mine didn't glow red bad igniters. After ordering the new parts install was easy and under 15 mins. My advice is to be careful pulling the oven out to access the back panels, be careful not to scratch your flooring. 5 screws for the big panel, and 3 for the small panel. All Phillips head screws. 5 inside the oven to pull the old igniter. Easy job anyone can do it. I did both upper and lower ovens and the broiler igniters.

Removed all the racks from inside the oven, unscrewed the 6 screws that held it into the cabinet, pulled it out and sat it on the floor in front of the cabinet. Removed the oven sensor from the inside of the oven after disconnecting the wire harness from the rear right exterior of the oven. Installed new sensor from inside (2screws), plugged it into the harness in the back and reinstalled oven in the cabinet.

I took the broiler pan out of the shipping container and put it in the oven.

Unplugged the old temp sensor at the back of the stove. From the inside I removed the 2 retaining screws. I taped a string to the old wire and pulled it through so I could pull the new harness through on the new sensor. When the new sensor arrived I installed it in reverse order. Easy peasy. Works great!!!!

The ignitor heated up and the broiler worked but not the bake mode. Repaired per instructions

I received my glass panel realy quick from Part Select. It was an eansy job to install the new pane.
It took less than an hour. Thanks for Your prompt service.

First I drilled out the screws on the burner as they were fused. I opened the stove top cover to access the underside of the burner. Removed the orifice holder, by disconnecting the gas line with a line Wrench and the electric cord.

The trick is to be careful with the gas line. Also when you go to replace the orifice holder you will notice that the holes are not threaded. The metal is soft and you're supposed to just screw the screws into the holes and let them bite into the metal. Then you reattach the gas on the electric and put the stove top back together.

This is a double oven unit. Both the upper and lower igniters are easy to get to, with just a few screws to remove. However in order to reach the quick disconnects, the back of the oven needs to be removed. So there are a bunch of screws to take off and the oven needs to be moved away from the wall. Pulling out the igniter wires and putting the new ones back in, is easy. Then put all the screws back on and move the oven back to the wall. Don't forget to disconnect the power when you do all this.

I had to wait week for parts that were supposedly in stock No notice about delay I had to call to find out you really dropped the ball on this one

Removed door, dissasembled door cleaned all broken glass, installed new glass, re-assembled door and put door back on oven.

Very simple project.

Super easy!! Your website was very clear about the fact that because my stove has two ovens, it would need two different types of racks. I almost three of the same type at another website until I realized it on yours. Bought two racks, one for the upper oven and only another for the lower one which is bigger and could take two racks, but out of an abundance of caution went for only one for the lower. I have now made pizzas in my (almost) new oven (it feels new because it’s finally usable!!) and made lasagna today for hubby’s birthday. Very happy with my purchase. The only thing was what seemed as an excessive packaging for two flat items. They were put into a flat box and then into a huge, voluminous one with bubble wrap and air filled bags. A little excessive for two metal items, it seemed to me, but otherwise, you have a happy customer. Thank you.

Put the back of stove on blocks of wood to get high enough to screw the new leg in.