MGR6775BDB Maytag Range - Instructions

Look in the oven. On the upper left corner is the sensor. Remove two screws. Gently pull the wire and connector through the hole and insulation. Disconnect old sensor, replace new. Gently push the connection through, then finish pulling through from behind the stove. Replace the screws inside the oven. Done.

easy-peasy remove small panel on back
disconnect in the back of range-oven "orange wire"
unscrew igniter from burner inside oven
remove and replace with new one
slide wire thru hole in back of oven
reconnect---u r done
dave

place new ones in by hand. the new ones fit too loose and if not carefull they will fall out.

I ordered the part one afternoon. It arrived before noon the next day. Then I simply removed the old seal (with about 2 dozen spring clips). Inserted the new part by carefully inserting the new seal into its corresponding hole at each end and then worked my way around the seal while inserting each attached spring clip into its corresponding hole.

Be prepaired to take the glass out. Unexpected, but not too hard. A right angle screw driver can be helpful for the bottom door. Takes some skill and patience. Good Luck! I am happy with the parts. Delivery time was quick.

The oven door comes off easily by opening to the first stop and lifting it straight off the hinge arms. I removed all of the small perimeter screws, removed the outer glass and the upper frame that the handle attaches to. Removed the broken handle and attached the replacement part. Re-assembled oven door and slid it back onto the hange arms. Piece of cake repair!!

Remove door, racks, unplug, remove lower burner cover two screws, the burner tube deflector pan two wingnuts, the burner tube. With igniter attached, remove back of range 4 screws to expose connector to igniter, unplug then remove burner tube, then igniter, replace igniter feed through back of oven wall and reconnect igniter reverse process and its done

Purchased 2 piece broiler pan from this site

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I then conected the new element and replaced te two screws. Turned on the oven & works fine.
Very Easy!

. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) pushed wires back in and secured sensor

I removed the door from the oven and set it on towel on the table, and started the repair of the door. I removed the screws one at a time, and one layer at a time. Becareful you need to take the whole door apart, and remember how it goes bact together. In the end it was worth it. The hardest part was getting the right part. I thought I could order the whole door, and found out after several calls they don't sell the whole door. Part Select both times I put in my order had the parts at my door within 2 to 3 days. I also had to return one of the parts and within 2 to 3 days the part was credited to my account

Clearly, the oven gasket was not the cause of the problem.
The hinge replacements did not fix the problem. I think the problem was that the hinge's mating part inside the door had been deformed, perhaps by leaning on the door when fully opened. I compensated for that by placing two stacked magnets near the upper hinge mounting screw hole on the inside of the oven body. (0.75" screws , 8-24 or metric equiv., needed for the upper screw location.) This gave the hinge about 15 degrees of additional door tilting force. In addition, I added 6 ceramic magnets across the top of the door mating surface, kudos to that website. Now it pulls fully flush with the magnets.
Ceramic magnets are good to 400+ degrees and they come in boxes of 120 for $12.00.
I only had one oven as a sample, but I could see what I thought was deformation on the inside of the oven door where the hinges are inserted. In this case, I think that makes (only) hinge replacement futile.
Sorry if this solution does not fit your marketing desire, but I did leave the new hinges installed.

I unplugged the power cord,removed the back panel and unplugged all the wiring harnesses.four screws hold the control in place. reverse to install. The instructions were very complete(I do this for a living so it was extra easy)Anyone following the directions could replace this in under 15 min.

I removed the two screws that attach the sensor to the oven wall. Then removed to more screws in the back of the oven and took off the rear cover, diconnected the sensor connector and installed the new sensor.

After reading some of the repair stories, I was hesitant about doing this task. It was really very simple, I just removed the screws from the back of the stove, and removed the old element. I then replaced it with the new one and replaced the back cover. This whole task from start to finish took 10 minutes. The oven heats perfectly now just like a new oven.