MER6772BAS Maytag Range - Instructions

We removed the rear panel, then removed the stove top, then removed the sides. We undid the straps that hold the insulation in place. Pulled out the old insulation and put in the new. Replaced every thing we took off. The nastiest thing was the old insulation full of mouse droppings and even a few dead mice.

Left oven off. Located sensor in pdf manual. Unscrewed mount, pulled sensor out to access connector. Disconnected old sensor, checked continuity(resistance) on ohms with multimeter. No continuity; connected new sensor, screwed mount back into place, turned on oven and baked cookies to check operation & it worked perfectly.

Removed the large lower back panel of range (6-8 phillips screws) which holds upper control back panel in place. Removed upper control back panel (2 screws), exposing infinite switch electrical connections. At front face of control panel, removed (pulled off) control knob, exposing 2 phillips screws holding switch in place. (NOTE: A sleeve is on the switch arm or maybe remains inside the control knob). Look for this sleeve. Without it, the knob will NOT seize the switch rotary arm.
Removed each wire connection individually, one at a time, installing it in the proper position on the new switch.
Reverse all procedures to put things back together. A very simple, straight-forward operation.

Our Maytag electric range has a small oven on top that doubles as a toaster, and food warmer. The lower one is a big oven suitable for Thanksgiving Turkey Etc. It is also a broiler as is the top oven. The top one had the bottom element burn out about 5 months back as well. Now the bottom element on the lower oven had burned out as well. The oven has some age on it, but when I looked to replace it I saw it would be approx $1800.00 - $2000.00 for a new one. I knew the elements were replacable and thought if I should call out the lonely guy, the Maytag repairman. Nope, I pulled the stove out disconnected the 220 power supply. I got the Model number off the back stamped info plate. I looked up Maytags parts on Google and the first one was PartSelect.com. They have easy fill-in spaces for Model and Make and a schematic of the oven and all it's pieces are visually displayed. I found the part I needed and ordered. It arrived in two days, very reasonable, very fast shipping. Pulling out the old elements required only a battery operated screw driver, a flash light, and a magnetic dish to keep track of the screws.The removal of the rear panel takes about 10 sheet metal screws. I marked the leads I disconnected by color with a felt tip pen on the back. I disconnected and removed the aforementioned clips, cleaned inside the oven and placed the new element in, reconnected everything on the back as it had been according to my color assignments, replaced the back with battery operated screwdriver from the magnetic dish, reconnected the 220V power supply. Done, in about 30 minutes; I saved a bunch over a new Stove and at least a couple hundred over a service call. Easy and satisfying.

turn off all electric to the wall oven. removed the old broiler. replaced the new broiler and turned on the electric. checked the brolier one to see if it worked....it did thanks for the customer service for her help in finding the replacement part.

First I reviewed a video on YouTube by this site. Even though the range on the video was not the same as mind, it gave me an idea on what to do. I proceeded to pull the rang out from the wall and disconnected the power plug. Next I removed two screws from the back located on the left and used a flat blade screw driver to depress two brackets on the front to release the glass top panel. I unplugged the wiring harness and disconnected the grounding wire and took the glass panel off and laid it upside down on the kitchen table. I removed the old heating element first by unplugging the wiring and removing the brackets that held it in place. Installed the new one, plugged in all wirings, brackets, screws and replace the top back on the stove.

It was really easy. It took about 5 minutes to remove the screws holding the back in place. Another couple of minutes to remove the switch, and a few more minutes to change the wires over one at a time. Then 5 more minutes to put it all back together again, and plug it back in, and it just worked. Really simple.

Removed 8 screws of retainer holding glass top to box.. Pulled 5 knobs and glass top and set aside. Popped 2 retaining clips holding burner , removed them and transferred to new burner (#12 and #48 position). Used wide blade screwdriver to facilitate removing terminals from old burner and attached terminals to new burner.Popped retaining clips into crossbeam, put glass top on and 8 screws back into retainer. Works great.

Ok this is a glasstop jenn air cce3531b, 5 burners, 11 years old. I am computer data entry employee and 56 years old. I have never done repairs myself in the past but decided to try. I ordered a new burner and indicator light as I wasnt sure which to replace. I found the main breaker and shut it off. I lifted the stovetop out of the counter opening by pushing it through the bottom and placed it on the counter with a towel under it, I had plenty of room to work so that was very easy. I used a nutdriver set to remove 12 screws and lifted off the top very carefully and placed it in the other room , since I had to repair unit thought I would also clean and replace the foam tape around the perimeter of the glasstop. Ok now I unscrewed 4 more screws with the nutdriver and replaced the indicator light, that took about 6 minutes so far. Then I turned the breaker back on and tested and it did not work. Turned breaker back off ,now I replaced the burner by lifting it out of the opening very easily, unscrewed with philips screwdriver 2 screws and the new burner was exactly the same as the existing one so I just slid the old connections off one at a time and replaced them as I went along onto the new burner, screwed it back into place and turned the breaker on and tested it and it worked. I now turned the breaker back off and took off the old foam tape from the glasstop and replaced with new, fit it back onto the base and screwed the 12 screws back in and placed it back into the counter opening and turned breaker back on and now all is fixed and I saved $100 dollars in labor fees. This took 35 minutes and was easy for me. Thanks you partselect

Removed door from oven by pulling up at the first stop point after opening the door. Removed the outer shell by removing 5 screws. Disassembled the inner door by removing 6 screws. Be careful with the insulation blanket (fits in a molded portion of the inner door). Glass windows can be removed (for cleaning) via a couple screws. Old gasket/seal is held in-place via spring-clips; just squeezed each clip, pushed each thru their respective holes, and pulled off the worn-out gasket. New gasket snapped in-place by pushing the clips thru the respective holes. Reverse the process to reassemble the door. You can do this job in 15-20 minutes. Took us longer because it took some elbow-grease (and patience) to clean the crud off the glass windows.

The repair was very easy. There were 3 screws under the front lip which had to be removed. This allowed the smooth glass top to be removed, tilt and pull forward. This exposed the burners and the unit I purchased was a direct replacemt for the burnt unit. All I had to do was remove the electrical clips from the old unit and put them on the new unit. There were 3 spring elements, each with 2 screws, which held the unit in place.

Waited for my husband to do it, but when he didn't, I tried it. Very simple! Just pulled the old gasket out of the pinch pin holes in the door, then replaced it. Tuck the one end into the hole at the bottom of the door, then match up the little pinch pins on the gasket with the holes in the door - matches up perfectly! Be sure to tuck in each of pinch pins till they sort of "snap" into each hole. Took me 5 minutes, tops. Works great now, no more lost heat around the edge of the door.

Took the old levelling leg out and screw the new one in.

Removed the approximatly 10 screws that hold on both the upper and lower pieces of sheet metal that cover the back of the oven. Removed the screw holding in the temp sensor. Unplugged and removed the old sensor. Plugged in and installed the new sensor (using one of the included adapter wires supplied with the sensor). Put the 2 pieces of sheet metal back on and plugged in the oven.

Real easy, I removed the two screws holding the element in place, then pulled the element out a few inches to reveal the wire connectors. pulled the connectors from the old element and then replaced with the new one and screwed it back into place and presto! All done and cooking again. The replacement part came in 2 days fast and reliable. Thanks PartSelect.com