MERH865RAS13 Maytag Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Paul D from GULF SHORES, AL
- Parts Used:
- W11197495
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken temp control knob
Able to get correct part!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from HILTON, NY
- Parts Used:
- W10823711
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Coil shorted out.
Removed cooktop, wiring and coil. Marked where wires went on limiter
tabs. Ordered coil 1200 Watt, received a 1500 one. Sent back to PS with prepaid shipping label {great}. New one had a different limiter tab arrangement. The instructions included warned this but doesn't tell you where to put the wiring. Instructions say to remove the old limiter and put it on the new coil but this can not be physically be done plus who would want an old limiter on a new coil.
Found a YOU TUBE video on how to test and place wires on limiter switches which shows the number letter sequence on the ceramic part. Maybe PS will put that info in their instructions. Coil works great !!
tabs. Ordered coil 1200 Watt, received a 1500 one. Sent back to PS with prepaid shipping label {great}. New one had a different limiter tab arrangement. The instructions included warned this but doesn't tell you where to put the wiring. Instructions say to remove the old limiter and put it on the new coil but this can not be physically be done plus who would want an old limiter on a new coil.
Found a YOU TUBE video on how to test and place wires on limiter switches which shows the number letter sequence on the ceramic part. Maybe PS will put that info in their instructions. Coil works great !!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mohaemd from pittsburgh, PA
- Parts Used:
- 74010546
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the oven door would not shut all the way, so heat was leaking
The part fit perfectly.Ther repair was logic. The door was of course heavy . I needed an extra hand.
I would have appreciated of instructions were included with the part. Also a web link on how to do it would alos have helped greatly
I would have appreciated of instructions were included with the part. Also a web link on how to do it would alos have helped greatly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Nashville, TN
- Parts Used:
- 12001656
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven door was locked, couldn't set oven temps
Got a bent metal coathook to temporarily release the oven door, removed the screws from the old probe, inserted the new one, and hooked it up, using the one of the plug adapters provided. Problem solved! The oven door latch was now disengaged, the oven would now accept temperature inputs, and the rear cooling fan (which wouldn't shut off) now turned off. That's a lot of things working better for less than $50!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from WEST CHAZY, NY
- Parts Used:
- W11562931, WP7403P239-60
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Oven gasket was worn out and front left burner only worked on high setting
After watching a couple of YouTube videos, I removed the old oven gasket and installed the new one. I then pulled the range out from its cubby, unplugged the power whip, and removed the upper access panel. After confirming that I had the correct replacement switch, I removed each wire separately and attached each to the new switch. I plugged the power cord back and tested the burner. It worked perfectly! I put everything back and I was back in business.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Lewiston, ID
- Parts Used:
- 74003645
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broken Inner Glass Pane
I received my glass panel realy quick from Part Select. It was an eansy job to install the new pane.
It took less than an hour. Thanks for Your prompt service.
It took less than an hour. Thanks for Your prompt service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sergio from JENSEN BEACH, FL
- Parts Used:
- W10823711
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Burner did not heat up
Access to burner nothing like on-line videos:
1) Remove 4 screws under front control panel. (Oven door needs to be open.)
2) Remove 2 flat head screws on sides of control panel. This will loosen control panel. Capture control panel to keep from hanging from wires/connectors. I used hooks made from a wire hanger.
3) Remove 2 screws to remove two steel panels on either side of stove.
4) Remove rear screw of the 2 front screws now exposed and 2 rear screws near top of stove.
5) Carefully flip over glass top being careful not to pull on the wires.
6) Identify burner to be replaced. Note 2 numbers where two clamps are attached to burner.
7) Using 3/8” nut driver, remove screws to allow removal of burner. Remove wires per included instructions. Remove burner.
8) Place new burner under clamps and align to the holes by the two numbers noted in step 6 above.
9) Connect wires to new burner as per included instructions.
10) Reverse removal steps.
1) Remove 4 screws under front control panel. (Oven door needs to be open.)
2) Remove 2 flat head screws on sides of control panel. This will loosen control panel. Capture control panel to keep from hanging from wires/connectors. I used hooks made from a wire hanger.
3) Remove 2 screws to remove two steel panels on either side of stove.
4) Remove rear screw of the 2 front screws now exposed and 2 rear screws near top of stove.
5) Carefully flip over glass top being careful not to pull on the wires.
6) Identify burner to be replaced. Note 2 numbers where two clamps are attached to burner.
7) Using 3/8” nut driver, remove screws to allow removal of burner. Remove wires per included instructions. Remove burner.
8) Place new burner under clamps and align to the holes by the two numbers noted in step 6 above.
9) Connect wires to new burner as per included instructions.
10) Reverse removal steps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rita from COOPERSBURG, PA
- Parts Used:
- W10823711
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Burned out burnrr
Went well. Husband, who has some appliance repair experience, did repair in less than a hour. Replacement burner was not an exact duplicate of original but he was able to adjust for that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Constance A. from SMITHFIELD, RI
- Parts Used:
- WP7701P523-60
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
The handle had broken away from the door
A neighbor used to own his own appliance store, and he was nice enough to remove the old handle and put the new one on for me.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allen from PISGAH FOREST, NC
- Parts Used:
- 74010546
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven door would not close tightly
Remove door
Remove front cover of door
Remove hinge screws
Put back together.
Remove front cover of door
Remove hinge screws
Put back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- judy from springfield, IL
- Parts Used:
- WP3608F092-71, 74008681
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
broken outer door glass
after i recieved the parts with the glass still laying on the foam pads it was packed in i put some soap on the bottom so the new bracket would slide on easier. i centered the bottom bracket on the bottom of glass and pushed in place. i then picked up glass and slid it up in place on oven door attached the screws on bottom done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from SOLON, IA
- Parts Used:
- 12001656
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven temperature fluctuates
Replaced the thermostat according to existing videos and had to adjust the thermostat using instuctions in the user manual for model CWE4800ACB.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marlene from ATHENS, MI
- Parts Used:
- WP74011675
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven handle was broke off
Removed the oven door an removed some screws. After that it was pretty much self explanatory from there. Real simple project !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from CENTERVILLE, OH
- Parts Used:
- WP7403P239-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Large burner was surging indicating infinite switch failed
Changing out the switch was easy. Paid attention to wire connections to avoid mixup. Removal and installation of the switch was easy. It's the back panels that gave me the most challenge. Used screwdrivers and needle nose pliers to do repair. Having a second set of hands for the two part back panel reinstall was most helpful, but can be accomplished by 1 person.
Burner works great. This is a easy DIY fix.
Burner works great. This is a easy DIY fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jane from BRYAN, TX
- Parts Used:
- W10823711
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Back left burner went out
I found on youtube Also we marked each wire with masking tape 1A and 1B, 2A and 2B. The wires were the same color.
Was this instruction helpful to you?
Thank you for voting!