MGR6775BDW13 Maytag Range - Instructions

Remove the door, remove screws from all sides

Remove sides and face of oven door by sliding down from under the oven handle trim.

Remove screws on 2nd light of glass and set aside.

Now you are at the inner door panes. their should be two in an insulated type unit.

Remove the remaining screws from the handle pracket and the permiter frame for the glass/insulation. Remove permiter frame and set aside.

Pull out inner door glass frame. get a pair of pliers and bend tab on frame up so you can pull the frame sightly apart, replace the glass, secure frame tightly around glass slide tab back into reciever slot and bend down ( you may need another person to assist in keeping both lights in the frame while trying to ben tab back in to place)

reassemble door as it came apart carefull not to over tighten the screws, they strip easy.

1. Lifted the oven door off the hinge mechanisms.
2. Removed the screws holding the bottom front glass support bracket.
3. Removed the bracket and the remaining broken glass from that support bracket.
4. Cleaned the new glass front with Glass Cleaner and slid it into the top support bracket.
5. Slid the previously removed bracket onto the glass and positioned that bracket back onto the oven door.
6. Re-installed the screws to hold the bracket and the new glass in place.
7. Slid the oven door back onto the hinge mechanisms on the stove.

From reading other reviews i thought I would have to dis-assemble the door but when I saw the new part I realized I would not have to, simply pop the beveled clips w/pocket knife and pop in the new seal clips. the ends tucked very nicely, an 80+ yr. old would have no trouble if they had their wits.

1. Turn power off and loosen and remove screws. Pull out sensor from mounting hole and expose wire connector. Remove old sensor. Select appropriate wire adaptor and reconnect the sensor. Carefully push connector through hole and secure with screws removed previously. Turn power back on and cycle oven to make sure oven operates properly. If you have an oven thermometer it can be used to compare set point of oven to thermometer to make sure readings are the same. All done! Happy wife can now bake cookies again and now I can go back to man cave for other projects!

Easy instal most of time was taking off and replacing back panel Found watching how to videos helpful

Put a new one in.

Removed door, oven racks, and cover at the bottom. Very easy to get to the actual ignitor. The more challenging part is getting to the back of the oven where the igniter plugs in. Once we got the oven pulled out enough to access the bottom of the back panel, we removed the back panel....just a couple screws and it slides up. Unclipping and removing the old igniter was easy. It's a bit of a challenge to feed the new igniter's wires under the insulation and up over a small ledge and out a small hole that's smaller than a quarter. Small hands help. You can avoid the whole part of attaching it in the back of you clip the wires of your old igniter and new one. Then use ceramic wire nuts to connect the new igniter the the old one's wires. We decided not to do that since it was already done once that way and figured it would be good to have fresh wires clipped in at the back. Overall, fairly easy repair especially if you decide to connect the igniter with ceramic wire nuts.

The entire "project" took me less than 3 minutes, and required no tools at all! First, the saleswoman over the phone pointed me to the correct product for my problem ($30 less than what I thought I needed), and it arrived at my home within 4 days. Then, it was just a matter of pulling off the old gasket, and snapping the new one in place! Simple!

I removed all the screws that held the trim and inner frame to the outside window unit first. Then, I removed a protective glass from over the two inner panes. Next after removing the frame that held the two inner glass panes together, I took the broken inner glass pane out and replaced it with the new one. Then basically I just retraced my steps and had the door put back together in about 45 minutes. You just need to pay close attention to your disassembly so that you are able to put the pieces back together quickly.

The best I can say is to remove door. take screws out from the bottom and sides first. Clean all layers of glass before installing handle.

replaced heat sensor

I repair it by shutting off the gas. removing the back panel of the stove . unplug the electrical sensor cord to the igniter. Then replace with new one.

We removed the door from the hinges by sliding it up. Then we removed all the screws holding the door together. We had to remove the screw securing the trim. Next we removed the screws inside the trim holding the old handle. We replaced the handle and trim and screws in reverse order. Finally, we re-attached the door by sliding it onto the hinges.

Door was removed very easily. Outside trim pieces were removed. The rest came apart like a simple puzzle. Inside glass is very easily accessed. Upon assembling, time was well under an hour. Shipping was fantastic and I saved close to 200dollars between a service call and a repair.

once I figured out how to remove door it was a piece of cake for a 72 year old man.